background image

4

Take care that the glow plug clip or battery leads do not come into contact with the propeller. 
Also check the linkage to the throttle arm. A disconnected linkage could also foul the propeller.

After  starting  the  engine,  carry  out  any  needle-valve  readjustments  from  a  safe  position  behind  the  rotating 
propeller. Stop the engine before attempting to make other adjustments to the carburetor.

Adjust the throttle linkage so that the engine stops when the throttle stick and trim lever on the transmitter are fully 
retarded.  Alternatively,  the  engine  may  be  stopped  by  cutting  off  the  fuel  supply.  Never  try  to  stop  the  engine 
physically.

Take care that loose clothing (ties, shirt sleeves, scarves, etc.) do not come into contact with the propeller. 
Do not carry loose objects (such as pencils, screwdrivers, etc.) in a shirt pocket from where they could fall through 
the propeller arc.

Do not start your engine in an area containing loose gravel or sand. The propeller may throw such material in your 
face and eyes and cause injury.

For their safety, keep all onlookers (especially small children) well back (at least 20 feet or 6 meters) when preparing 
your  model  for  flight.  If  you  have  to  carry  the  model  to  the  take-off  point  with  the  engine  running,  be  especially 
cautious. Keep the propeller pointed away from you and walk well clear of spectators.

Warning! Immediately after a glowplug-ignition engine has been run and is still warm, conditions sometimes exist 
whereby  it  is  just  possible  for  the  engine  to  abruptly  restart  if  the  propeller  is  casually  flipped  over  compression 
WITHOUT the glowplug battery being reconnected. Remember this if you wish to avoid the risk of a painfully rapped 
knuckle!

NOTES

5

NOTES WHEN APPLYING
AN ELECTRIC STARTER

Do  not  over-prime.  This  could 
cause  a  hydraulic  lock  and 
damage  the  engine  on  application 
of the electric starter.

If  over-primed,  remove  glowplug, 
close  needle-valve  and  apply 
starter  to  pump  out  surplus  fuel. 
Cover  the  head  with  a  rag  to 
prevent  pumped  out  fuel  from 
getting into your eyes.

Summary of Contents for IL-300



















Reviews: