manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 22 FlexCAN

MPC5602P Microcontroller Reference Manual, Rev. 4

538

Freescale Semiconductor

 

The FlexCAN module stores CAN messages for transmission and reception using a Message Buffer 
structure. Each individual MB is formed by 16 bytes mapped on memory as described in 

Table 22-4

. The 

module also implements two additional Message Buffers called SMB0 and SMB1 (Serial Message 
Buffers), in the address ranges 0x60

–

0x6F and 0x70

–

0x7F, which are not accessible to the end user. They 

are used for temporary storage of frames during the reception and transmission processes. 

Table 22-4

 

shows a Standard/Extended Message Buffer (MB0) memory map, using 16 bytes total (0x80

–

0x8F space).

0x08C0–0x08FF

Rx Individual Mask Registers RXIMR16–RXIMR31

on page 559

0x0900–0x3FFF

Reserved

Table 22-3. FlexCAN register reset status

Register

Affected by hard reset Affected by soft reset

Module Configuration Register (MCR)

Yes

Yes

Control Register (CTRL)

Yes

No

Free Running Timer (TIMER)

Yes

Yes

Reserved

Rx Global Mask (RXGMASK)

Yes

No

Rx Buffer 14 Mask (RX14MASK)

Yes

No

Rx Buffer 15 Mask (RX15MASK)

Yes

No

Error Counter Register (ECR)

Yes

Yes

Error and Status Register (ESR)

Yes

Yes

Interrupt Masks 1 (IMASK1)

Yes

Yes

Interrupt Flags 1 (IFLAG1)

Yes

Yes

Serial Message Buffers (SMB0–SMB1) – Reserved

No

No

Message Buffers MB0

–

MB15

No

No

Message Buffers MB16

–

MB31

No

No

Rx Individual Mask Registers RXIMR0–RXIMR15

No

No

Rx Individual Mask Registers RXIMR16–RXIMR31

No

No

Table 22-4. Message Buffer MB0 memory mapping

Address offset

MB field

0x0080

Control and Status (C/S)

0x0084

Identifier Field

0x0088

–

0x008F

Data Field 0 

–

 Data Field 7 (1 byte each)

Table 22-2. FlexCAN module memory map (continued)

Offset from

FlexCAN_BASE

0xFFFC_0000

Register

Location

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

MADRIX AURA Technical Manual & Quick Start Manual preview
AURA
Brand: MADRIX Pages: 36
GCE S 400 Operating Instructions Manual preview
S 400
Brand: GCE Pages: 24
mikroElektronika ETH WIZ click Quick Start Manual preview
ETH WIZ click
Brand: mikroElektronika Pages: 3
Window Master WMU 831 Installation Instructions Manual preview
WMU 831
Brand: Window Master Pages: 7
Raypak RAYTHERM 624 Specifications preview
RAYTHERM 624
Brand: Raypak Pages: 2
AGRI TRONIX DIGI-STAR GT400 Operator'S Manual preview
DIGI-STAR GT400
Brand: AGRI TRONIX Pages: 26
Badger Meter MDS 2000 User Manual preview
MDS 2000
Brand: Badger Meter Pages: 66
NI cRIO-9065 Features preview
cRIO-9065
Brand: NI Pages: 28
Magpowr DIGITRAC 2 Instruction Manual preview
DIGITRAC 2
Brand: Magpowr Pages: 22
Baldor Nextmove ESB Installation Manual preview
Nextmove ESB
Brand: Baldor Pages: 98
digitalview 417100041-3 Instructions Manual preview
417100041-3
Brand: digitalview Pages: 30
Rexroth Indramat DURADRIVE SYSTEM200 Project Planning Manual preview
DURADRIVE SYSTEM200
Brand: Rexroth Indramat Pages: 86
ITRON RB 4700 Series Instruction Manual preview
RB 4700 Series
Brand: ITRON Pages: 44
red lion LP1090 Installation Manual preview
LP1090
Brand: red lion Pages: 2
SAJ 8000m-2S1R5GH User Manual preview
8000m-2S1R5GH
Brand: SAJ Pages: 59
YASKAWA Motoman NXC100 Manual preview
Motoman NXC100
Brand: YASKAWA Pages: 60
Danfoss FCM305 56 Instruction Manual preview
FCM305 56
Brand: Danfoss Pages: 132
Oase InScenio EGC Operating Instructions Manual preview
InScenio EGC
Brand: Oase Pages: 332

Brands by name

Popular brands

Load more brands