NXP Semiconductors OM40006 User Manual Download Page 22

 

 

NXP Semiconductors 

UM11079 

 

IoT Module base board 

UM11079_OM40006.docm 

All information provided in this document is subject to legal disclaimers. 

© NXP B.V. 2017, 2018. All rights reserved. 

User manual 

Rev. 1.0 

— March 20, 2018 

22 of 23 

11.  List of tables

Table 1.

 

Jumpers ............................................................ 6

 

Table 2.

 

LEDs, buttons and connectors .......................... 8

 

Table 3.

 

P4 connections ............................................... 14

 

Table 4.

 

Host Expansion Header signals ...................... 15

 

Table 5.

 

Expansion connectors ..................................... 16

 

Table 6.

 

Expansion Connector signal sharing ............... 16

 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for OM40006
























Reviews: