NXP Semiconductors LPC1102 User Manual Download | Manualshive

Page: 97 / 258

background image

UM10429

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2010. All rights reserved.

User manual

Rev. 1 — 20 October 2010

97 of 258

NXP Semiconductors

UM10429

Chapter 11: LPC1102 SPI0 with SSP

11.6.9 SPI/SSP Interrupt Clear Register

Software can write one or more one(s) to this write-only register, to clear the
corresponding interrupt condition(s) in the SPI controller. Note that the other two interrupt
conditions can be cleared by writing or reading the appropriate FIFO or disabled by
clearing the corresponding bit in SSPIMSC registers.

11.7 Functional description

11.7.1 Texas Instruments synchronous serial frame format

shows the 4-wire Texas Instruments synchronous serial frame format supported

by the SPI module.

Table 98:

SPI/SSP Masked Interrupt Status register (SSP0MIS - address 0x4004 001C) bit
description

Bit

Symbol

Description

Reset Value

0

RORMIS

This bit is 1 if another frame was completely received while the
RxFIFO was full, and this interrupt is enabled.

0

1

RTMIS

This bit is 1 if the Rx FIFO is not empty, has not been read for
a “time-out period", and this interrupt is enabled. The time-out
period is the same for master and slave modes and is
determined by the SSP bit rate: 32 bits at PCLK / (CPSDVSR

×

[SCR+1]).

0

2

RXMIS

This bit is 1 if the Rx FIFO is at least half full, and this interrupt
is enabled.

0

3

TXMIS

This bit is 1 if the Tx FIFO is at least half empty, and this
interrupt is enabled.

0

31:4

-

Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.

NA

Table 99:

SPI/SSP interrupt Clear Register (SSP0ICR - address 0x4004 0020) bit description

Bit

Symbol

Description

Reset Value

0

RORIC

Writing a 1 to this bit clears the “frame was received when
RxFIFO was full” interrupt.

NA

1

RTIC

Writing a 1 to this bit clears the Rx FIFO was not empty and
has not been read for a timeout period interrupt. The timeout
period is the same for master and slave modes and is
determined by the SSP bit rate: 32 bits at PCLK / (CPSDVSR

×

[SCR+1]).

NA

31:2

-

Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.

NA

«
...
95
96
97
98
99
...
»

Summary of Contents for LPC1102



































































































































































































































































Reviews:

No comments

Related manuals for LPC1102

Brand: H3C Pages: 69

Brand: Federal Signal Corporation Pages: 34

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: Icar Pages: 40

Brand: Icar Pages: 86

Brand: Icar Pages: 39

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

CEmarking RCX221

Brand: Yamaha Pages: 468

Brand: iluminize Pages: 2

Brand: Vageo Pages: 2

Brand: DirectConnect Pages: 2

Brand: Belimo Pages: 6

Kaysun KC-03.2 SPS

Brand: Frigicoll Pages: 44

Mannesmann DKC21.3

Brand: Rexroth Indramat Pages: 38

Brand: Sinclair Pages: 36

Brand: Solvis Pages: 44

Brand: NHRC Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands