NXP Semiconductors KITVR5510 A0EVM Series, User Manualline, Page: 10 / 32

NXP Semiconductors
UM11587
KITVR5510xA0EVM Evaluation Kit User Guideline
Jumper Function Position Description
1 – 2 shorted STANDBY pin pulled up to VPRE
2 – 3 shorted STANDBY pin to GND J15 STANDBY I/O control
open (default) STANDBY pin controlled by FRDM-K82F board
1 – 2 shorted BUCK1_OUT as VCOREMON input
J60
VCOREMON source
selection
2 – 3 shorted
(default)
BUCK1/BUCK2_DUAL_PHASE_OUT as VCOREMON input
1 – 2 shorted VSUP 2 as HV_HDLVO input
J70
HDLVO high-voltage
input source selection 2 – 3 shorted
(default)
VPRE_OUT as HV_HDLVO input
1 – 2 shorted
(default)
BUCK1_OUT as LV_LDLVO input
J71
HDLVO low-voltage
input source selection
2 – 3 shorted VPRE as LV_HDLVO input
1 – 2 shorted 1P8V
J72
Voltage setting for
VDDIO external
regulator (J8: 9–10)
selection
2 – 3 shorted
(default)
3P3V
1 – 2 shorted Pull up to VDDIO
J82
PGOOD pin and pull-
up source control
2 – 3 shorted
(default)
Pull up to VPRE
1 – 2 shorted Pull up to VDDIO
J83
RSTB pin and pull-up
source control
2 – 3 shorted
(default)
Pull up to VPRE
J95 Not used 1 – 2 (default open)
1 – 2 shorted
(default)
VMON1 = VPRE (3.3 V)
3 – 4 shorted
(default)
VMON2 = BUCK3 (1.1 V)
5 – 6 shorted
(default)
VMON3 = LDO2 (1.8 V)
7 – 8 shorted
(default)
VMON4 = LDO1 (1.8 V)
9 – 10 shorted VMON4 = BOOST (5 V)
J101
Regx outputs to
VMONx (divided down
to 0P8V) connection
11 – 12 shorted VMON4 = External (0.8 V)
1 – 2 shorted
(default)
Feedback from capacitor close to inductor
J102 VPRE feedback
selection
2 – 3 shorted Feedback from external source, if needed
1 – 2 shorted Feedback from the load
J103 BUCK2 feedback
selection
2 – 3 (default) Feedback from capacitor close to inductor
1 – 2 shorted Feedback from the load
J104 BUCK1 feedback
selection
2 – 3 shorted
(default)
Feedback from capacitor close to inductor
1 – 2 shorted Feedback from the load
J105 BUCK3 feedback
selection
2 – 3 shorted
(default)
Feedback from capacitor close to inductor
open (default) BUCK1/BUCK2 in Single Phase
SJ3
BUCK1/BUCK2
Multiphase
configuration
shorted BUCK1/BUCK2 in Dual Phase
open
SJ4
BUCK1 Single/
Multiphase
configuration
shorted (default) BUCK1 in both Single and Multiphase
Table 2. Jumpers
...continued
UM11587 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2021. All rights reserved.
User manual Rev. 1 — 3 May 2021
10 / 32