NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 638 | Manualshive

Page: 638 / 1325

background image

Table 31-3. MDM-AP status register assignments (continued)

Bit

Name

Description

1 Flash is ready.

2

System Security

Indicates the security state. When secure, the debugger does not have
access to the system bus or any memory mapped peripherals. This field
indicates when the part is locked and no system bus access is possible.

NOTE: This bit is not valid until Flash Ready bit set.

0 Device is unsecured.

1 Device is secured.

3

System Reset

Indicates the system reset state.

0 System is in reset.

1 System is not in reset.

4

Reserved

5 – 15

Reserved for future use

Always read 0.

16

Core Halted

Indicates the core has entered Debug Halt mode

0 Core is not halted.

1 Core is halted.

17

Core SLEEPDEEP

SLEEPDEEP=1 indicates the core has entered Stop mode.

18

Core SLEEPING

SLEEPING=1 indicates the core has entered Wait mode.

19 – 31

Reserved for future use

Always reads 0.

31.3.2 MDM-AP Control register

Table 31-4. MDM-AP Control register assignments

Bit

Name

Secure

Description

0

Flash Mass Erase in Progress

Y

Set to cause mass erase. Cleared by hardware after mass erase
operation completes.

1

Debug Disable

N

Set to disable debug. Clear to allow debug operation. When set, it
overrides the C_DEBUGEN field within the DHCSR

disable Debug logic.

2

Debug Request

N

Set to force the core to halt.

If the core is in Stop or Wait mode, this field can be used to wake the
core and transition to a halted state.

3

System Reset Request

Y

Set to force a system reset. The system remains held in reset until
this field is cleared. When this bit is set, RESET pin does not reflect
the status of system reset and does not keep low.

4

Core Hold

N

Configuration field to control core operation at the end of system
reset sequencing.

0 Normal operation—release the core from reset along with the rest
of the system at the end of system reset sequencing.

Table continues on the next page...

SWD status and control registers

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

638

NXP Semiconductors

«
...
636
637
638
639
640
...
»

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

Brand: ABB Pages: 128

Brand: UniKey Pages: 20

Brand: Altronix Pages: 8

Brand: nvent Pages: 6

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

Brand: EFI Pages: 127

Brand: maxxess Pages: 11

Brand: SOLARJACK Pages: 14

Brand: H3C Pages: 11

Brand: Nanjing Putian Datang Information Electronics Co., Ltd. Pages: 2

Brand: DUNIWAY Stockroom Pages: 30

Brand: G-Tech Pages: 26

Brand: OCL Pages: 2

Brand: J+J Pages: 91

SmartControl RS232

Brand: Savant Pages: 2

Brand: Zapi Pages: 36

Brand: Electrosmith Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands