Connecting NV-226J-PV at Camera End
Connect the black power conductor to the
camera’s negative power terminal. Connect the
red lead to the camera’s +12VDC power terminal.
Then connect the Male BNC to the camera’s video
output.
Connect a factory-crimped RJ45 patch cable
(rather than unreliable field-crimped RJ45s)
between the NV-226J-PV and an adjacent female
RJ45 jack. Straight-through wiring pinouts are:
Connecting PVD at the Power Supply
Cable Integrator
Bring the 4-pair PVD cable from each camera back
to the location of the Power Supply Cable Integrator.
NVT recommends that an RJ45 Patch Panel be used
here in conjunction with RJ45 patch-cords. Use of
these EIA/TIA 568B compliant practices allows for
easy testing with an RJ45 (LAN) tester, as well as
moves and changes.
The Power Supply Cable Integrator may be one of:
NV-216A-PV
or
NV-218A-PVD
single channel
device.
NV-704J-PVD
or
NV-716J-PVD
in conjunction
with a multi-output power supply with individually
floating outputs. Most conventional multi-output
power supplies employ a bus architecture which is
unsuitable for this application.
NV-4PS10-PVD
or
NV-16PS10-PVD
in conjunc-
tion with a passive or active receiver hub, such as
the NV-413, NV-813(S), NV-1613(S), NV-3213(S),
NV-442, NV-452R, NV-842, NV-1642, NV-3242, NV-
872, NV-1672 or NV-3272.
NV-4PS13-PVD, NV-8PS13-PVD, NV-16PS13-
PVD, NV-8PS42-PVD, NV-16PS42-PVD,
or
NV-32PS42-PVD
For further instructions, please refer to the installa-
tion manual for the selected receive-end equipment.
Technical Specifications
Video
Passive Transceiver
DC to 10 MHz 0.5 dB typ
Common Mode/Differential
Mode Rejection
15 KHz to 10 MHz 60 dB typ
Power
Input voltage 13 to 30 VAC/DC
Class II SELV floating power supply
Output voltage 12VDC, regulated
Output current 400 mA
Wires
Two 5” (125mm)
18 AWG (1mm)
Black -
Connectors and Impedance
RJ45 UTP input
100 ± 20 ohms
Male BNC output
75 ohms
Environmental
Temperature
-4 to 167° F (-20 to 75° C)
Humidity
0 to 95% non-condensing
Transient Immunity per ANSI / IEEE687 C62.41
Mechanical
Size
1.52 in (38,6 mm) wide
2.27 in high (5,77 mm)
0.8 in deep (2,03 mm)
[Excluding connectors]
Product Weight
1.8oz (50g)
Packaged Weight
0.16lb (0,07kg)
Agency
The NV-226J-PV is listed and/or conforms to the
following certifications and directives:
UL listed to UL2044 or UL/IEC60065 cUL Listed to
CAN/CSA22.2 No.1 for Canada CE mark under
EMC and low voltage directives for the European
Union.
Complies with FCC part 15B limits
Troubleshooting
If you are experiencing problems, check the RJ45
pinouts. Check with an RJ45 tester. NVT recom-
mends factory crimped RJ45 cables. Avoid field
crimping. Test each segment of a long cable run
independently. Attempt to isolate the problem.
Attempt to simplify your setup. View the camera’s
video output locally. Measure AC and DC voltages.
Power the camera locally.
Customer Support
NVT customer support can be reached 8:00 AM to
5:30 PM Monday through Friday.
US Office:
(+1) (650) 462-8100
US Fax:
(+1) (650) 326-1940
UK Office:
(+44) (0)20 8977 6614
UK Fax:
(+44) (0)20 8973 1855
Email USA:
www.nvt.com/email
Email UK:
www.nvt.com/email
Web home page: www.nvt.com
Returns
Please call before returning units to NVT. Returned
materials must have a “Returned Materials
Authorization” (RMA) number from NVT marked on
the outside of the shipping carton.
Limited Lifetime Warranty
NVT warrants that the product conforms to NVT’s
applicable published specifications and is free of
defects for the life of the product. There shall be no
other warranties, express, statutory, or otherwise,
including any implied warranty of merchantability,
of fitness, or any other obligation on the part of NVT
with respect to any of the products.
In the event that any of the products is damaged,
altered, or modified without the express written
consent of NVT, any warranty for those products will
cease and NVT will have no further liability as it per-
tains to those products.
NVT assumes no responsibility for damages or
penalties incurred resulting from the use of this
product in a manner or location other than for which
it is intended.
NVT’s liability under any warranties shall be dis-
charged by replacing or repairing any part or parts
which do not conform to the applicable warranty
under normal and proper use. NVT’s liability with
respect to any product shall not exceed a refund of
the price received by NVT for that product, and in no
event shall NVT have any liability for any incidental,
consequential, special, or indirect damages.
Some states do not allow the exclusion or limitation
of special, incidental, or consequential damages, so
the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights,
and you may also have other rights which vary from
state to state.
Specifications subject to change without notice.
Power Distance Chart
Copyright © 2012 Network Video Technologies, Inc.
451-226-1-E 07/12
RoHS
Fixed 12VDC Camera used with
NV-226J-PV
Power Supply Voltage
1,586ft (478m)
1,999ft (609m)
795ft (242m)
1,002ft (306m)
2,220ft (677m)
2,799ft (853m)
1,113ft (339m)
1,403ft (428m)
B&W Camera, 2.4 W
2-pair 24 AWG
2-pair 23 AWG
Color Camera 4.8 W
2-pair 24 AWG
2-pair 23 AWG
24 VAC
28 VAC
