manualshive.com logo in svg

nVent RAYCHEM NGC-40 DEMO UNIT, User Manual, Page: 26 / 51

Share
Download
nVent RAYCHEM NGC-40 DEMO UNIT User Manual Download Page 26

nVent.com 

|

 26

Raychem-AR-H

58686

-NGC

40

DemoUnit-EN-

1805

Step 

12

 –

 Ground Alarm / Trip

Create a ground fault alarm by rotating the ground fault knob slowly clockwise until the  
NGC-

40

-HTC module alarms. The ground-fault alarm will not trip the output OFF. Observe the ground fault current on the 

Circuit Overview

 

screen.

•  Continue rotating the ground fault knob until the NGC-

40

-HTC module trips. This trip current will cause the output to turn OFF.

•  Rotate the ground fault knob fully counterclockwise. 
•  Use the alarm list to reset the alarm. 
•  Click on the 

Monitor Device

 Tab.

•  Review – What you accomplished 
•  How to setup a circuit using the basic mode for an NGC-

40

-HTC module. This includes High and Low temperature alarms, control 

setpoint, High and Low current alarms and ground fault alarms.

•  How to view alarms using the alarm list.
•  How to reset an alarm from the alarm list.
•  How to reset an alarm from the NGC-

40

-HTC module.

•  How to identify a module using the Module Identification button. 

  IMPORTANT:

 Use the steps outlined in this section to configure the second NGC-

40

-HTC module and NGC-

40

-HTC

3

 module.

Summary of Contents for NGC-40 DEMO UNIT




















































Reviews:

No comments