Nuvation Energy NUV100-CI-12-1 Product Manual Download Page 33 | Manualshive

Page: 33 / 109

background image

4.4.2. Connect Temperature Cable



The Stack Switchgear is pre-configured to expect a defined number of thermistors
based on the information provided to Nuvation Energy during order fulfillment.
Failure to use the same number of thermistors will result in undesirable Stack
Switchgear behavior. Please contact

[email protected]

change requiring a Stack Switchgear configuration update.

The Temperature cable provides 10 kΩ NTC thermistors for temperature measurement of the cells
and/or surrounding area. These sensors are used by Nuvation Energy BMS to detect over and under
temperature conditions and adjust battery current limits to compensate for cell temperature.

Figure 24. 2 Thermistor cable (NUVW-A18A12-020)

Figure 25. 7 Thermistor cable (NUVW-A19A12-020)



2 to 7 thermistors are supported to accommodate systems requiring Nuvation
Energy BMS to meet functional safety requirements.

Cable Isolation

Because the sensors are referenced to the

CELL0

or

BLOCK0

input on the Cell Interface, care must be

taken to ensure that they are electrically isolated from any common or ground potential, and from
all other cell voltage terminals of all Cell Interface modules in the system

The thermistors must be isolated from the cell voltage terminals, as well as any metal work or
other exposed conductors, in such a way that they will not make an electrical connection to a cell
terminal in the event of vibration/failures.

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

29

Rev 1.2, 2021-03-03

Curie Update 1

«
...
31
32
33
34
35
...
»

Summary of Contents for NUV100-CI-12-1














































































































Reviews:

No comments

Related manuals for NUV100-CI-12-1

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

Brand: Fantech Pages: 2

Brand: Feig Electronic Pages: 153

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: Tamas Pages: 12

Brand: Tait Pages: 3

Brand: Wang Pages: 68

Brand: NAVITAS Pages: 14

Brand: Saluki Pages: 13

Liberty Vertical Picket

Brand: National ramp Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands