background image

 

OPERATION MANUAL

 

 

 

IBS 40002210 

Page | 10 

V13 (January 2019) 

Installation 

 

 

WARNING 

Installation  of  these  units  should  be  carried  out  by  appropriately  qualified  and  skilled 
personnel. Failure to do so may invalidate the warranty. 

 
The equipment will be delivered to site boxed on a pallet. 
 
Remove all packaging materials from the unit and dispose of correctly, in accordance with local regulations. 
 
Care must be taken when removing packaging so not to damage or scratch the painted, glass or stainless 
steel surfaces. 
 
Remove all temporary tape. 
 
Prior to the first use, clean with a proprietary cleaning solution, following the manufacturers’ instructions. 
Refer to the cleaning and maintenance section of this document. Ensure that excessive water is NOT used. 
Do NOT use abrasive detergents. 
 
If there  are any signs of damage, contact  The Alan Nuttall Partnership Ltd immediately. Failure  to report 
faults, defects or missing items upon delivery may incur charges. Deliveries must only be signed off if they 
are in a satisfactory condition. 
 
Ensure that safe manual handling practices are employed at all times. The unit should be lifted into position 
using the correct lifting procedures, in line with local and regional safety policies. 
 
The following considerations must be given to the site of installation: 
 

 

Avoid placing sources of heat near the appliance. 

 

Do NOT  install the appliance  near other equipment that generates high temperatures  in order to 
avoid damage. 

 

The equipment should be sited so that it is not affected by draughts from doors or air conditioning 
systems. Temperature fluctuations are likely to occur if the equipment is not  sited appropriately. 
This will have an adverse effect on product temperatures and may increase running costs. 

 

Ensure that the floor supports the weight of the unit at full capacity. 

 

Ensure that the unit is installed on a flat, even surface. 

 
The supporting or surrounding surfaces for the appliance must be: 
 

 

Non-combustible; 

 

Level, flat and even; 

 

Able  to  support  the  appliances  weight  at  full  load,  without  undergoing  deformation  or  structural 
failure; 

 

Immovable. 

 

Summary of Contents for Flexeserve Zone FXZNA10N2S51
























Reviews: