background image

Page 4

MODELS  754RBNT • 754SNNT

USE AND CARE

USE AND CARE

WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND

LOCK OUT SERVICE PANEL BEFORE CLEANING OR SERVIC-

ING THIS UNIT.

BULB REPLACEMENT

Remove glass shade. Replace bulbs as required. Replace glass

shade.
Use 60 Watt (maximum) candelabra base, incandescent bulbs.

MOTOR LUBRICATION

The motor is permanently lubricated. Do not oil or disassemble

motor.

CLEANING

TO CLEAN GLASS SHADE AND GRILLE PAN:

Remove glass shade. Shade can be wiped clean with a mild deter-

gent solution or glass cleaner and dried with a soft cloth. Remove

2 bulbs. Grille pan may be gently vacuumed and wiped clean with

a soft cloth. Never use abrasive cloth, steel wool pads or scouring

powders on glass shade or grille pan. METAL AND ELECTRICAL

PARTS SHOULD NEVER BE IMMERSED IN WATER.

TO CLEAN FAN ASSEMBLY:

Remove grille pan and unplug fan assembly (black receptacle).

Gently vacuum fan, motor and interior of housing.  METAL AND

ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WA-

TER.

SERVICE PARTS

WARRANTY

99043894A

NUTONE ONE YEAR LIMITED WARRANTY

NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase.

THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which

have been subject to misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above

limitation may not apply to you.

NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL NOT

BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone: 1-800-637-1453, (b) give the model number and part identification and (c) describe the nature

of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

NuTone, Inc.,

 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)

KEY PART NO.

DESCRIPTION

1

97016702

Glass Shade

2

97016701

Shade Mounting Hardware (754RBNT)

97016704

Shade Mounting Hardware (754SNNT)

3

99260428

Motor Nut, #6-32 Hex (2 req.)

4

99150618

Grille Screw

5

99080522

Motor

6

99110446

Blower Wheel

7

99270981

Lamp Receptacle, White

8

99270982

Motor Receptacle, Black

9

98009612

Wiring Panel

10

99150471

Ground Screw

11

99170245

Screw, #8-18 x 3/8”

12

98008868

Wiring Plate

13

97014185

Damper/Duct Connector

14

97014922

Housing Assembly

A

99525297

Light Fixture Assembly (754RBNT)

99525296

Light Fixture Assembly (754SNNT)

(Light Fixture Assembly includes

Glass Shade (Key No. 1), Mounting

Hardware (Key No. 2), and Grille Pan

Assembly (B))

B

97016700

Grille Pan Assembly (754RBNT)

97016703

Grille Pan Assembly (754SNNT)

C

97015312

Blower Assembly

(Includes Key Nos. 3 thru 6)

D

97015171

Wire Panel Assembly

(Includes Key Nos. 7, 8, 9)

Order replacement parts by “PART NO.” - not by “KEY NO.”

2

3

4

5

6

7

8

9

11

12

13

14

A

C

D

10

B

1

2

Summary of Contents for 754RBNT









Reviews: