manualshive.com logo in svg

Nugen 7000XTR, Service Manual, Page: 24 / 44

Share
Download
Nugen 7000XTR Service Manual Download Page 24

Page 2

Control Valve Assembly

  Item No. 

Quantity 

Part No. 

Description

.

1................. 1.............................. 61050.........................

Valve Body Assy, 7000, 32mm Dist

.

2................. 1..............................

6152-10

....................

Piston Assy, 7000, Softener, D/F 35GPM

.

...................................................

6153-10

....................

Piston Assy, 7000, Softener, D/F 28GPM

.

...................................................

6152-20

....................

Piston Assy, 7000, Filter 35GPM

.

3................. 3.............................. 40576.........................

Clip, H, Plastic, 7000

.

4................. 1.............................. 61438.........................

Seal & Spacer Kit, 7000, D/F

.

5................. 1..............................

60016-01

....................

Brine Valve Assy, 7000, 560CD

.

6................. 1.............................. 40577.........................

Turbine Meter Assy, 7000

.

7................. 1.............................. 61XXX........................

Injector Assy, 7000

.

.

.

.

 

 

 

 

Part Number 

Injector Number

 

 

 

 

615-000

.............

#000

 

 

 

 

615-00

...............

#00

 

 

 

 

615-0

.................

#0

 

 

 

 

615-1

.................

#1 

 

 

 

 

 

 

 

 

615-2

.................

#2

 

 

 

 

615-3

.................

#3

 

 

 

 

615-

.................

#

 

 

 

 

615-5

.................

#5

61500-7000EXP_REVC

Summary of Contents for 7000XTR













































Reviews:

No comments