background image

Care and cleaning tips

Caution!

Improper handling of the speaker may result in damage. 

• Always unplug the speaker before cleaning it!

• Before recommissioning, make sure that all connections are cor-

rect, that there are no short circuits and that the speaker is com-

pletely dry.

• Never use strong cleaning agents or solvents such as petrol, spir-

it or similar!

Enclosure

We recommend commercial window cleaner sprayed onto a cotton 

cloth. This allows almost all fingerprints and dust to be easily re-

moved. Alternatively, you can also use window active foam.

We advise against the use of microfibre cloths! These can cause 

mini scratches in the surface.   

Diaphragms and Speaker Chassis

To remove dust from a loudspeaker chassis, a lint-free cotton cloth 

is sufficient to wipe the membrane lightly with very little pressure. 

The tweeters of all Nubert loudspeakers are equipped with a pro-

tective grille so that they can also be wiped off with low pressure. If 

the dust cannot be completely removed, a make-up brush from the 

drugstore is suitable.

Service

If you have any questions or problems during the commissioning of 

your Nubert system, please do not hesitate to contact our service 

team:

Phone:

 

0800 68 23 780 (toll-free, within Germany) 

0049 7171 92690-118 (international)

E-mail:

[email protected]

Please have your customer number ready!

Technical Data nuPro X-3000

Principle 

Fully Active HiFi/Studio/Multimedia 

Loudspeaker 

2-Way Bass Reflex System

Drivers 

1x Tweeter with 25 mm fabric dome 

1x 148 mm bass-midrange driver  

with polypropylene composite cone

Power of built-in amplifiers  2x 150 Watt (rated power) 

2x 220 Watt (music power)

Frequency response 

38 – 22 000 Hz  +/- 3 dB 

40 – 20 000 Hz  +/- 2 dB

Input sensitivity 

1 V for analog gain +6 dB 

2 V for analog gain +0 dB

Max. Input 

4.5 V

rms

Standby power consumption  0.7 Watt (single / pair) 

1.8 Watt (wls master / wls slave) 

To change the mode of operation, please see page 11
Maximum sampling rates at 

all digital connections 

24 bit / 192 kHz

Radio frequency bands and    radio transmitting power 

Bluetooth module: 

2402 – 2480 MHz   9,75 dBm / 9,5 mW 

Network module  

(wireless mode): 

5180 – 5240 MHz   15,75 dBm / 37,6 mW 

5736 – 5818 MHz 

15,75 dBm / 37,6 mW

Dimensions (H x W x D) 

30 x 18.5 x 23 cm 

(D incl. amplifier)

Weight 

6.6 kg

!

15

EN 12/2019 · E1

2

 

· 

nuPro X-3000

Summary of Contents for nuPro X-3000

















Reviews: