NuAire NU-5710 Operation And Maintenance Manual Download Page 57

Page: 57 / 64

OM0249

Page 57 of 64

Rev 4 June/2020

13.8 Heat Rejection:

14 BTU/Minutes.

14.0 Disposal and Recycle

Incubators

that are no longer in use and are ready for disposal contain reusable materials. ALL components with the

exception of the HEPA filters may be disposed and/or recycled after they are known to be properly disinfected.

Note:

Follow all local, state and federal guidelines for disposal of HEPA filter solid waste.

Prior to any disassembly for disposal the incubator must be decontaminated

Component

Material

Incubator Cabinet

Painted Steel

Outer Door

Painted Steel

Chamber

Stainless Steel

Outer Door Gasket

Vinyl Clad Magnet

Inner Door Gasket

Silicon Rubber

Front Service Panel

Painted Steel

Electronics Panel

Painted Steel

Sensor Bay

Aluminum

Exhaust Filter

Aluminum

Hosing

Silicon Rubber

Tubing

Stainless Steel

Air Pump

Various Steel/Copper/Nylon

Motor

Various Steel/Copper/PVC

Printed Wiring Assembly

Lead Free Electronic

Wire

PVC Coated Copper

Solenoid Valves

Various Steel/Copper

Connectors

PVC

Hardware

Stainless Steel and Steel

Note:

Material type can be verified with use of a magnet with stainless and aluminum being non-magnetic.



BIOHAZARD

RECYCLE



LEAD FREE

CAUTION

Summary of Contents for NU-5710

































































Search results

Summary of Contents for NU-5710

Reviews:

Brands by name

Popular brands

NuAire NU-5710, Operation And Maintenance Manual

Search results

Summary of Contents for NU-5710

Reviews:

Brands by name

Popular brands