manualshive.com logo in svg

NuAire NU-5710, Operation And Maintenance Manual

Share
Download
NuAire NU-5710 Operation And Maintenance Manual Download Page 35

OM0249 

Page 35 of 64 

Rev 4 June/2020 

 

 

 

General Options 

1.

 

Door Close Delay Time 

 

This value determines the time, in seconds, to increase the door and parameter heater to duty cycle by 10% after 

the inner door is closed.  Also inhibits gas and RH control for the same period. 

2.

 

Air Inject Time 

 

This value specifies the time, in seconds, for an injection of air into the chamber 

3.

 

Air Inject Cycle Time 

 

This value specifies the amount of time in minutes between each injection of air into the chamber 

4.

 

Digital Output Interval 

 

This parameter specifies the frequency, in minutes that performance and set point data is output to a device such 

as a printer that is only capable of receiving data.  If the frequency is specified as zero, no data will be output. 

5.

 

Door Ajar Alarm Delay 

 

Determines how long in minutes the glass door can be open before an alarm is declared. 

7.

 

Settings (text located at the top of screen) 

 

Pressing the next button will go to the second page containing the following: 

•

 

The Filter Maintenance button to access:

 

 

Resetting the change filter notice

 

 

Setting time to reminder (

24 months/

1/48) 0 disables the feature.

 

 

View time remaining until current notice is triggered. 

 

•

 

The Clear Password button that clears the 4 digit password that was input through the Set Password 

screen.

 

•

 

Change language Button:  Pressing this button brings up a screen with the language choices of English 
(default), Spanish, French & German.  Pressing the button in that screen of the language desired will 
change the user screens to that language. 

•

 

Screen Lock button (default Main Screen Unlocked).  Pressing this button will change it to “Main screen 
Locked” (Lockout = 1).  This puts a “Press to unlock” button on the Nuaire Logo in the Main screen.  This 
feature stops accidental screen changes by brushing the touch screen.  You must press and hold (2 
seconds) until the message disappears which unlocks the main screen so that you can navigate into; the 
System settings, Alarms, Environmental Set Point and Clock Adjustment screens.  Pressing the button 
again will change the text to “Main Screen Unlocked (Lockout = 0).  This removes the “Press to Unlock” 
button from the Nuaire Logo and the Main screen goes back to the default condition. 

•

 

Power Loss Mode cancel button.  Cancels Power loss mode.  Only use this if it is certain that there is no 
condensation in the circulation system.  See Section 10.2 for further details about the Power Loss Mode. 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for NU-5710

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands