background image

4

nuaire.co.uk 

029 2085 8400

19. 02. 19. Document Number  671881

Installation Manual

NOXMASTER - PIV with Carbon Filtration

5.0 ELECTRICAL CONNECTION

5.1 Electrical Details

Voltage:  

230V 1ph 50Hz

IMPORTANT

The fan unit is also supplied with a fused spur. The three core 

mains cable from the unit should be connected to a fixed 

wiring installation, via the spur, in accordance with current IEE 

wiring regulations.

5.2 Wiring Diagrams

5.2.1 NOXMASTER (All Versions Without Heater)

1A Fused Spur

(Supplied)

2 Pole Isolator

(By Others)

MAINS

230V

50Hz

N

L

Blue

Brown

Supply cord

from unit

Green/yellow

IMPORTANT

The electrical connection of the unit must be carried out by 

a qualified electrician. 

For good EMC engineering practice, the power supply output 

cable and any sensor cables should not be placed within 

50mm of other cables or each other.

4.3.3 Dual Inlets

The unit features a dual inlet which automatically selects the air source 
based on the surrounding temperature. To utilise this feature, the 
circular guard needs to be knocked out and the supplied spigot fitted 
(ensure the lose guard is removed from the unit). If ducted air supply is 
not being used, 

do not knock out guard.

Fix the required spigot to the unit with the screws provided and 
seal with silicone to eliminate air leakage.

Duct to the outside using ridged ducting. 

Spigot 

Guard - Punched 

out and removed

150mm inlet 
duct to outside

Soffit grille (Part No. 775229) fixes over rectangular 
ducting which has been pulled through the rectangular 
hole (220mm X 80mm) cut in soffit and folded flat up 
against the surface of the soffit.
Note that a minimum soffit width of 130mm is required.

Form end of 
rectangular ducting 
to fit connector 
and secure using 
dynotie connector.

150mm dia. 
insulated ducting 
connected to unit 
spigot using 
dynotie connector
(Part No. FLDI150).

220mm x 90mm flexible 
PVC Rectangular ducting 
(Part No. PVC933WH). 
Note: this duct should 
be kept as short as 
possible.

Circular duct connector
(Part No. RDC150).

150mm dia. insulated ducting

connected to unit spigot using

dynotie connector
(Part No. FLDI150). 

150mm dia. pipe

(Part No. PVC130-6WH).

Insulated duct formed over pipe 

and sealed with dynotie connector.

199 x 215 x 20mm 

white plastic wall grille 

(Part No. PVC604WH).

Figure 7. Fitting Dual Inlets

Figure 8. Soffit Installation

Figure 9. Wall Installation

Ceiling 

Joist

Metal 

Mounting 

Bracket

A.V.

Mount

A.V.

Mount

Washer

3” Woodscrew

50mm 

Min.

12mm 

Clearance 

Hole

Control Output

Time Clock (controls bypass damper)

Thermostat (controls intake damper)

Heater Output

Figure 4. Anti-Vibration Mount Installation

Figure 5. NOXMASTER-HEAT Installation

Figure 6. NOXMASTER-HEAT Installation

Summary of Contents for NOXMASTER








Reviews: