background image

8

27. 11. 17. Leaflet Number 671733

Technical or commercial considerations may, from time to time, make it necessary to alter the design, performance and 

dimensions of equipment and the right is reserved to make such changes without prior notice.

10.0  Replacement  of Parts

Should any component need replacing Nuaire keep extensive

 

stocks

 

for  quick delivery. Ensure that  the unit  is  electrically  isolated, before

 

carrying  out  any  work.
Note: The supply  cable must  be replaced  by  an  electrically 
competent

 

person. 

When  ordering  spare parts, please quote the serial number  of  the

 

unit  and  the ARC  number of  the purchase if  possible.

(This  information  will  be  available  on  the fan  label).

11.0 Warranty

The 5 year warranty starts from the day of delivery and includes parts 
and labour for the first year and parts only for the remaining 4 years. 

This warranty is void if the equipment is modified without authorisation, 
is incorrectly applied, misused, disassembled, or not installed, 
commissioned and maintained in accordance with the details contained 
in this manual and general good practice.

The product warranty applies to the UK mainland and in accordance 
with Clause 14 of our Conditions of Sale. Customers purchasing from 
outside of the UK should contact Nuaire International Sales office for 
further details.

12.0 After Sales Enquiries

For technical assistance or further product information, including spare 
parts and replacement components, please contact the After Sales 
Department.

Telephone 02920 858 400

Installation and Maintenance

The WM2 Wall Mounted Range of Units

Summary of Contents for ecosmart MRXBOX95-WM2-AE









Reviews: