CYFAN-C EXTRACT FANS
INSTALLATION AND MAINTENANCE
7
3.4 Fan installation
Note: Semi-Recessed mounting requires the optional mounting kit:
(Part number: CYFAN-RKIT).
Installation must be completed by qualified personnel. A solid non
reverberant mounting position must be selected and passages for
ductwork from the outlet spigot, as well as electrical connection
prepared. Compatible ductwork should have already been installed.
3.5 Required tools
Drill, PH2 Screwdriver, Terminal Screwdriver and Tape Measure.
Fig 13. Semi-Recessed mounting frame kit suitable for 100mm and
125mm dia duct, consists of mounting plate and mounting flange.
3.6 Installation procedures
1. Unpack the fan unit and other components, and ensure that all
parts listed on page 1 are present. If not please contact the
manufacturer for replacement / missing parts.
2.
Place the front cover and inlet grille to one side.
3.
Remove 4 off No8 x
3
⁄
8
inch Pozi screws from the rear of the
unit. This allows the exterior case to be removed and disposed of.
4.
Remove the PCB cover by removing 2 off No6 x
1
⁄
2
inch screws.
Fig 14. Removal of PCB cover from casing.
5.
Partially remove the PCB assembly from the fan casing by
placing a finger tip behind the dip switches and pulling the PCB
away from the fan casing. (see fig 14).
6.
Disconnect and remove the fan scroll from assembly and
completely remove the PCB assembly. Note: if the pull cord is
not required, remove it completely.
7.
Prepare an opening 205mm x 185mm in the mounting position.
8.
Position the mounting bracket in the previously prepared
aperture so that the ends of the bracket are flush with the
surface of the wall. Secure the bracket top and bottom with
suitable fixings (by others).
9.
Drill and plug (if necessary) the mounting surface.
10. Feed wiring flex through the back of the fan casing and
mounting plate.
11. Secure the case to the surface (fixings supplied by others). Note:
care must be taken not to twist or distort the case whilst fitting.
12. Partually replace PCB into the fan casing and wire flex into the
terminal block (see wiring options on page 5).
13. Replace fan scroll assembly and plug motor into PCB, replace
PCB fully into position by pushing the dip switches.
14. Replace PCB cover by fitting with 2 off No6 x
1
⁄
2
inch screws.
(see point 2 of the procedure).
15. Fit semi-recessed mounting flange to case using 4 off No4 x
3
⁄
8
inch screws.
16. Fit front inlet grille using 4 off No6 x
3
⁄
4
inch screws found in
the fixing kit.
17. Remove rubber gasket and adjust control to required settings
(shown in section 4). Once required settings are complete and
desired airflow rate is achieved replace rubber gasket.
18. Complete the fan installation by fitting (push fit) the front cover.
Fig 15. Ceiling mounting using the Semi-Recessed mounting kit.
First cut an aperture for the fan in the ceiling, cut and fit (A) timber
supports (not supplied) and fit fan as shown. Note: Remove the
shutters from the spigot if you are mounting CYFAN in the ceiling.
Note: pull-cord must be removed.
1.1 Installation Procedures cont.
Fit fan grille to inner fan case
using 4 fixing screws (No 6 x 3/4").
Push fit fan cover
to fan grille.
Fix fan skirt to inner fan case using
4 of fixing screws (No4 x 3/8").
Ensure plate edge is flush
with the suface of the wall
for a flush fit.
Use 4 off M4 x 16 screws
to secure inner fan case
to the mounting plate.
Mounting plate to be
placed within previously
prepaired aperture/opening
(205mm x 185mm)
fix into place using appropriate
fixings (supplied by others).
Fan grille.
Fan motor.
Semi-recessed mounting flange.
Inner fan
case.
Fan cover.
SECTION 3.0
FITTING THE PRODUCT
SEMI-RECESSED MOUNTING
PCB assembly
PCB cover
Mounting
Plate.
A
A
A
A
Ceiling.
10. 05. 17. Leaflet Number 691500
Ceiling.