background image

3

Limitations

 

The audio input of the VOPEX-C5SVA-x S-Video/Audio Splitter/Extender is compatible with the following
standard CPU audio outputs:

  Line out - typically lime green in color

  Speaker out- typically orange in color

  Headphone out- typically located on the CD-ROM

 

The audio outputs of the VOPEX-C5SVA-x Video/Audio Splitter/Extender and the ST-C5SVA-R-600
Receiver are compatible with self-powered stereo speakers.

Preparation for Installation

 

Locations should be chosen for the displays and speakers that also have space to connect the VOPEX-
C5SVA-x and ST-C5SVA-R-600 Receivers within the distance provided by the cables.    If extension cables
are needed, contact NTI for the cables required.

 

The CAT5 cables must be run to the locations where the VOPEX-C5SVA-x and ST-C5SVA-R-600
Receivers will be connected.   Be careful to route the cables away from any sources of magnetic fields or
electrical interference that might reduce the quality of the video signal  (i.e. AC motors, welding equipment,
etc.).  

NOTE

:  If CAT5 cable is already installed in the wall and there are RJ45 wall outlets, it will be

necessary to obtain male-to-male straight through connection cables long enough to reach from the wall
outlets to the connection locations of the VOPEX-C5SVA-x and ST-C5SVA-R-600 Receivers.

 

A properly grounded, polarized, and preferably surge-protected 120V or 240V electrical outlet (depending
on the AC adapter being used) must be installed close enough to the connection location of the VOPEX-
C5SVA-x and ST-C5SVA-R-600 Receivers, displays, stereo speakers, and A/V sources to plug them into.

 

All cables should be installed in such a way that they do not cause stress on their connections to the
equipment.   Extended lengths of cable hanging from a connection may interfere with the quality of that
connection.    Secure cables as needed to minimize this.

 

Properly shut down and disconnect the power from the video source, displays and stereo speakers to be
separated.    If other equipment is involved whose connections are being interrupted, be sure to refer to the
instruction manuals for that equipment for proper disconnection and re-connection procedures before
proceeding.

Preparation for Installation

Limitations

Summary of Contents for XTENDEX VOPEX-C5SV-x















Reviews: