NTI SM-4X2-15V-LC Installation And Operation Manual Download Page 41

NTI VEEMUX VIDEO MATRIX SWITCH 

 

37

 

 

 

 

SCAN   

 

ƒ

 

Pressed to toggle the scan enable/disable feature for the selected port 

ƒ

 

Must be preceded by an output port number (1 or 2 digits),  or the * (Asterisk) button to toggle all ports

 

Note: If the dwell time for a port is set for 0 seconds, it will not be scanned (page 28) 

 

AUDIO                 

THIS BUTTON IS NOT USED FOR THIS PRODUCT

  

 

 

VOL + / -        

THIS BUTTON IS NOT USED FOR THIS PRODUCT

       

 

 

MUTE Audio              

THIS BUTTON IS NOT USED FOR THIS PRODUCT

 

 

 

PREV -THIS BUTTON IS NOT USED FOR THIS PRODUCT 

 

Operation 

               Operation  of  the  IRT-UNV  is  intuitive.  The number of button presses required to complete any operation is kept to a 
minimum. This is accomplished using intelligent software within the NTI Matrix Switch. Additionally, the Matrix Switch allows for 
multiple ways for the user to complete the same operation – ensuring that the Remote will work as expected, regardless of who 
uses it. 
 

Note: For models with audio support, these commands will switch the video and audio signals simultaneously.   For 
independent video and audio switching using the IRT-UNV, see “Independent Video and Audio Control”  on page 

Error! 

Bookmark not defined.

.  

 

Changing Ports 

The first, and most important operational use of the IR Remote is changing ports of the switch.   This requires th

selection of both input and output ports. There are several methods of control. 

Channel Surfing 

The “IN +/-“ and “SCAN” buttons can be used to surf through input port connections. However, since there are multiple 

outputs/users, the question becomes “which output connection is being changed?”  As a result, it is required that an output be 
selected prior to using the “IN +/-“ buttons. 
 

The output port can be selected in two ways:  

 

by pressing the “OUT” button before selecting the output port number 

 

by pressing the “OUT” button after selecting the output port number 

 

                In  both  cases,  the  user  must  enter  the  output port number using the Numeric Keys (0-9). However, when the “OUT” 
button is pressed prior to selecting the port number, there will be a two (2) second delay after the last digit of the output port is 
entered that must expire before the output port is accepted. To avoid this delay, press the “ENTER” button to immediately accept 
the port number. 

Once the output port has been accepted, there will be a five (5) second timeout, during which the user must press 

another button (“IN +,” IN -,” or “SCAN”). Each subsequent press of “IN+” or “IN-“ will renew the timeout, waiting for you to press it 
again (to advance or go back by one more Input channel).  If no new command is sent to the switch before the timeout expires, 
the switch will forget the selected output, and pressing the “IN +/-“ buttons will have no effect. 

All output channels can surf inputs at once by pressing the “ * “ button prior to pressing the “IN +/-“ buttons. 
 
 
 

Examples: 

 
Change connection of Output 1 from Input 1 to Input 3: 
 
<

OUT

> + <

1

> + wait 2 s <

IN+

> + <

IN+

<

OUT

> + <

1

> + <

ENTER

> + <

IN+

> + <

IN+

>  (must press <

IN+>

 within 5 seconds of pressing <

ENTER>

 <

1

>   + <

OUT

> + <

IN+

> + <

IN+

>     (must press <

IN+>

 within 5 seconds of pressing <

OUT>

 
 
 
 

Summary of Contents for SM-4X2-15V-LC















































Reviews: