background image

READ BEFORE INSTALLING OR SERVICING
BATTERIES TO PREVENT PERSONAL INJURY

.

*

ALWAYS

 wear eye protection and protective clothing when

    working with the batteries.
* The batteries contain 

ACID

. Avoid contact with skin or clothing.

*

 ANTIDOTE:

EYES

       - Flush with water 15 minutes, Call physician.

INTERNAL

 - Drink water or milk.

Follow with Milk of Magnesia, beaten egg or
vegetable oil.
Call physician.

* Service should be done only by authorized, trained personnel.
* Charge batteries in a well ventilated area with the battery
   compartment opened by raising the recovery tank.

*

Batteries generate explosive gases - keep sparks, flames,

   burning cigarettes, or other ignition sources away at all
   times.

* Never lay anything on top of batteries, to prevent arcing.
* Turn off all switches during installation and service.
* To maintain machine balance, always slide batteries into position
   as shown on the battery installation decal.
* Connect the batteries as shown on the battery installation decal

to avoid shorting out the batteries and the electrical system.

* Disconnect the battery leads before performing any service or
    repairs.
*

ALWAYS

 make sure the battery charger is turned off when

  connecting / disconnecting to machine to prevent sparking.

STORAGE

*

ALWAYS 

store machine indoors in a dry, cool area.

*

ALWAYS

 empty and rinse clean the solution and recovery tanks

after every use.

*

ALWAYS

 remove and clean the squeegee assembly after every

use.

*

ALWAYS

 remove the pad driver or brush after every use.

*

NEVER

 store machine near furnaces, boilers or open flames

which may damage machine.

*

NEVER

 store any item on the machine.

*

ALWAYS

 protect the machine from freezing temperatures.

BATTERY INSTALLATION INSTRUCTIONS

Summary of Contents for WRANGLER 20W/D

























Reviews: