NSS STALLION 12 SC Operation Manual Download Page 7

 

 

OPTION - ACCESSORY CLEANING 

Preparing the Accessories: 

  Select the correct tool for the job to be performed. 

  Connect the solution hose to the quick connect at 

the back, lower left side of the machine and on the 
tool. 

  To connect a tool, pull back on the collar of the 

quick connect, insert one end of the solution hose 
fitting and push it in until it locks.  Attach the other 
end of the solution hose to the tool in the same 
manner. 

  Remove the machine hose from the 

right side

 of 

the vacuum lid and insert one end of the recovery 
hose into the lid.  Attach the other end of the hose 
to the accessory tool.

 

Cleaning upholstery, stairs or confined areas: 

  Prepare the solution / recovery tanks as you would 

for normal carpet cleaning. 

  To begin cleaning, turn on the rocker switch for the 

solution pump and vac motor only.  When you 
squeeze the trigger of the accessory tool it will 
spray the cleaning solution, release the trigger to 
stop the spray.

 

 

Do not apply water more than twice in one area 
to prevent excess wetting. 

  Over-wetting can damage upholstery and / or 

fabric.

 

Priming the Solution Pump 

During normal use the clean solution tank may run 
dry.  This will allow air to enter the pump and solution 
lines.  Air in the solution lines will prevent the pump 
from working properly, you must prime the pump.

 

  Refill the solution tank. 

  Disconnect any accessory tool that may be in use. 

CAUTION 

- place machine near a floor drain prior to 

the next step.

   

  

  Turn on the solution pump switch. 

  Depress the center pin in the accessory quick 

connect for 60 - 90 seconds (minimum).  The pump 
will spray air and solution out until all of the air has 
been forced from the solution lines.  When all of the 
air has been expelled you may resume your 
cleaning operation. 

NOTE:

 The solution pump will not prime through the 

spray jets or an accessory tool.

 

Summary of Contents for STALLION 12 SC











Reviews: