NRS Healthcare EASYFIT PLUS MK2 User Instructions Download Page 4

4

NRS HEALTHCARE

 Sherwood House, Cartwright Way, Forest Business Park, Bardon Hill, Coalville, 

Leicestershire, LE67 1UB, UK.

Tel. Customer Services: 0345 121 8111

Email: [email protected]

NRS Healthcare is a leading supplier of community equipment and daily living aids, to 

view our full range, visit our website:

www.nrshealthcare.co.uk

P63991-UI-1

Repeat steps 1, 2 and 3 until you start to feel tension 
and the bed rail feels secure.
It is recommended that the bed rail is checked at 
monthly intervals, to make sure it is securely 

fi

 xed 

to the bed.
If the bed rail has become loose, it must be re 
secured using the correct tightening lever method 
for your bed type.

Note: 

If the bed rail cannot be re-tightened 

su

  ciently, it must be removed and reinstalled.

REMOVING THE BED RAIL

The bed rail can be removed by turning the tightening 
lever anti-clockwise a few turns until the bottom of 
the handrail touches the base plate. Then release 
the 2 ratchet clamps.

CLEANING

Clean regularly using a general purpose, neutral 
detergent and warm water.
Please check the suitability of the cleaning product 
before use. Do not use abrasive cleaners or cloths 
as these could permanently damage the surface and 
invalidate any warranty.
To disinfect, wipe with a dilute bleach solution, and 
rinse thoroughly with fresh water.
This product is suitable for thermal decontamination 
and can be steam cleaned or autoclaved on cleaning 
cycles up to 80°C.
Allow product to fully dry prior to use/storage.

MAINTENANCE

Inspect the product at regular intervals and before 
re-use for signs of general wear or damage.
Any suspected faults or damage should be reported 
to the supplier immediately and the product taken 
out of use.

ACCESSORIES & SPARE PARTS
P64016: 

Spare Ratchet Clamp Kit

1.  LH and RH Ratchet Clamp Assembly (Pair)
2.  Ratchet Rack x 2
3.  Ratchet Rack Screws x 6

P11863:

 Spare Parts Kit

1.  Rubber Pads for Clamp Assembly x 4
2.  Base Feet x 4
3.  Base Tube End Caps x 2
4.  Tightening lever x 1
5.  Base Pin O’rings x 4
For more details please visit our website:
www.nrshealthcare.co.uk or call Customer Services.

PRODUCT DISPOSAL

This product must be cleaned thoroughly before 
disposal.
This product is manufactured from metal and plastic 
and can be disposed of through Local Authority 
Household Waste and Recycling Centres or through 
Local Trade Waste Collectors.

PRODUCT GUARANTEE

NRS Healthcare guarantee this product for a period 
of 12 months, from the date of purchase, against 
faulty materials and workmanship.
This guarantee does not cover; abuse, misuse, 
interference or tampering with any part of the product.
Any guarantee issued by NRS Healthcare does not 
a

 ect your statutory rights.

Summary of Contents for EASYFIT PLUS MK2

Page 1: ...Kg 25st ALWAYS ensure that the mattress is as close as possible to the bed rail Any gap could allow the client to become wedged in between DO NOT use on electrically height adjustable beds unless the height adjustment function has been disabled as this could damage the bed rail and or the bed frame when operated ALWAYS ensure the bed rail is firmly clamped to the bed frame Check regularly to ensur...

Page 2: ... Turn the tightening lever clockwise until you start to feel slight tension Do not over tighten as this will start to lift the handrail assembly off the base frame FITTING TO THE BED Make sure that the floor surface is level and even The bed base must be at least 30mm above the floor and clear of obstructions 1 Slide the Bed Rail Under the Bed Slide the bed rail under the bed in an approximate posi...

Page 3: ...tart to feel tension and the bed rail feels secure Note Lightweight beds may raise off the floor when tightening the tightening lever If this happens slacken the lever until all four corners of the bed are in contact with the ground 2 Divan and Low Bed Frame Tightening Full turns of the tightening lever may not be possible on some divan and low frame beds Use the following steps to adjust the bed r...

Page 4: ...isinfect wipe with a dilute bleach solution and rinse thoroughly with fresh water This product is suitable for thermal decontamination and can be steam cleaned or autoclaved on cleaning cycles up to 80 C Allow product to fully dry prior to use storage MAINTENANCE Inspect the product at regular intervals and before re use for signs of general wear or damage Any suspected faults or damage should be ...

Reviews: