manualshive.com logo in svg

NRG Systems 11174, Instructions Manual

Share
Download
NRG Systems 11174 Instructions Manual Download Page 2

NRG INSTRUCTIONS

 

 

 

SRA System | Soiling Measurement Kit

  

 

 
 
 

SRA Soiling Measurement Kit Instructions      
Rev. 6.0 

[email protected] | Page 2 

1 November 2017 

 

TABLE OF CONTENTS 

INTRODUCTION 

4

 

MATERIALS & TOOLS 

4

 

Inside the Kit ................................................................................................................. 4

 

Required Tools .............................................................................................................. 4

 

SECTION 1: ASSEMBLING THE SOILING MEASUREMENT KIT 

5

 

1.1 Open and unpack all items. ..................................................................................... 5

 

1.2: Mount upper U-bolt to tower, ................................................................................ 6

 

1.3: Mount PV panel assembly to upper U-bolt. ............................................................. 7

 

1.4: Attach the angle adjustment boom to PV assembly. ............................................... 8

 

1.5: Mount the angle boom to the tower. ...................................................................... 9

 

1.6: Adjust the PV panel angle. .................................................................................... 10

 

1.7: Secure & tighten all hardware. ............................................................................. 11

 

SECTION 2: WIRING AND MOUNTING THE INTERFACE MODULE 

12

 

2.1: Connect the 4C cable. ........................................................................................... 12

 

2.2: Mount DIN rail to shelter box back plate............................................................... 13

 

2.3: Wire the PV panels to the interface modules. ....................................................... 13

 

2.4: Mount the IMT Tm-V-4090 Temperature Amplifier Boxes. .................................... 14

 

Summary of Contents for 11174






















Reviews:

No comments

Brands by name

Popular brands

Load more brands