background image

TA600038-EN0/0

 

-  1  -

 

1. Introduction 

Thank you for considering our PCL6125 Evaluation Board(PCL6125-EB). 

This manual describes the specifications, functions of our PCL6125 Evaluation Board(PCL6125-EB) and how to connect and 

use it. Be sure to read this manual thoroughly and keep it handy in order to use the product appropriately. 

 

1.1 How to use this manual 

1.  Reproduction of this manual in whole or in part without permission is prohibited by the Copyright Act. 

2.  The contents of this manual are subject to change without the prior notice along with the improvement of performance and 

quality. 

3.  Although this manual is produced with the utmost care, if there are any questions, errors or omissions, please contact our 

sales representative. 

 

 

1.2 Product warranty 

1.2.1 Warranty period 

The warranty period is one year from the data of the delivery to an assigned place. 

 

1.2.2 Warranty scope 

If any defect is found in a product during the warranty period under the normal use following this document, NPM will repair or 

replace the product without charge.   

However, the following cases are not covered by the warranty even during the warranty period. 
1)  Products modified or repaired by anyone other than NPM or a person authorized by NPM. 

2)  Defects that result from dropping after the delivery or mishandling in transit. 

3)  Natural deterioration, wearing, and fatigue of components.   

4)  Defects result from any usage other than the original described in this manual. 

5)  Defects result from natural disaster or force majeure such as fires, earthquakes, lightning strikes, winds, floods, salts 

or electrical surges. 

6)  Defects or damages result from a cause that is not the fault of NPM. 

 

Products exported outside Japan are not covered by the warranty. 

When the product is purchased from a supplier other than NPM, please contact that supplier regarding the product’s warranty. 

Free repairs will only be conducted at NPM locations; no repairs will be made by business trips.   

Warranty period of repaired product is the same as the warranty period before repair.   

This warranty covers the product itself. The detriments or damages induced by the product failure etc. will not be covered by 

the warranty. 

 

 

 

 

 

 

 

 

Summary of Contents for PCL6125






























Reviews: