background image

NVIP-3C7000D-P, NVIP-5C7000D-P User’s manual(short form) ver.1.0 

All rights reserved © AAT Holding sp. z o.o.  

 

IMPORTANT SAFEGUARDS AND WARNINGS 

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives 
 

 
CE Marking 

 

Our products are manufactured to comply with requirements of the following directives and national regulations 
implementing the directives:  
 

Electromagnetic compatibility EMC 2004/108/EC. 

Low  voltage  LVD  2006/95/EC  with  further  amendment.  The  Directive  applies  to  electrical 
equipment  designed  for  use  with  a  voltage  rating  of  between  50VAC  and  1000VAC  as  well  as 
75VDC and 1500VDC. 

WEEE Directive 2002/96/EC 

 

Information on Disposal for Users of Waste Electrical and Electronic Equipment 

 
 

This  appliance  is  marked  according  to  the  European  1000VAC  Directive  on  Waste  Electrical  and  Electronic 
Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will 
help to prevent potential negative consequences for the environment and human health, which could otherwise 
be caused by inappropriate waste handling of this product. 
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be 
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and 
electronic equipment for recycling purpose. For more information about recycling of this product, please contact 
your local authorities, your household waste disposal service or the shop where you purchased the product. 

 

RoHS Directive 2002/95/EC 

Out of concern for human health protection and friendly environment, we assure that our products 
falling  under  RoHS  Directive  regulations,  regarding  the  restriction  of  the  use  of  hazardous 
substances  in  electrical  and  electronic  equipment,  have  been  designed  and  manufactured  in 
compliance with the above mentioned regulations. Simultaneously, we claim that our products have 
been tested and do not contain hazardous substances whose exceeding limits could have negative 

impact on human health or natural environment 

 

Information 

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self 
installation in households by individuals without technical knowledge. 

 

Excluding of responsibility in case of damaging data on a disk or other devices:  

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices 
during device operation. 

 

WARNING! 

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN 

USER’S  MANUAL  AND  OTHER  DOCUMENTS  DELIVERED  WITH  THE  PRODUCT,  OR  IF  IT  DOES 

NOT  ARISE  FROM  THE  USUAL  APPLICATION  OF  THE  PRODUCT,    MANUFACTURER  MUST  BE 

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S  RESPONSIBILITY FOR 

THE RESULTS OF SUCH AN ACTION. 

Summary of Contents for NVIP-3C7000D-P























Reviews: