Novus DC80L Owner'S Manual Download Page 6

4.1.

 

MODEL DC80R GENERAL SPECIFICATIONS 

Maximum voltage allowed between any terminal and earth ground or between the 

two input terminals: ............................................................................................ 30 V 
Resolution: ................................................. RTD 0.1 °C / °F; Resistance 0.01 / 0.1 Ω 
Storage temperature: ........................................................................ -40 °C ~ 60 °C 
Operating temperature: ..................................................................... -10 °C ~ 55 °C 
Operating altitude: ................................................................. 3000 meters maximum 
Temperature coefficient: ................ ±0.01 % / °C (0 °C ~ 18 °C and 28 °C ~ 50 °C) 
Relative humidity: ............................................................................ 95 % up to 30 °C 

 ....................................................................................................................... 75 % up to 40 °C 

 ....................................................................................................................... 45 % up to 50 °C 

 ........................................................................................................ 35 % up to 55 °C 
Shock:........................................................................... Random 2 g, 5 Hz to 500 Hz 
Safety: ............................................................................................ 1 meter drop test 
Power requirements: ...............................................................6 x AAA 1.5 V Battery 
Size:................................................................................. 205 mm x 98 mm x 46 mm 
Weight: ............................................................................. 472 g (including batteries) 

 
 
 
 
 
 
 

4.2.

 

MODEL DC80R FRONT PANEL 

The keypad and display functions are shown below: 

 4-wire input terminal (not used 

for output) 

 2-wire input / output terminal 
 2-wire input / output terminal 
 3-wire input terminal (not used 

for output) 

 Power ON / OFF switch 
 RTD type selection key 
 °C / °F selection key 
 INPUT/OUTPUT selection key  
 Fast increment key (simulation) / 

wire mode selection 

(measurement) 

 Fast decrement key (simulation) / 

wire mode selection 

(measurement) 

 Increment key  
 Decrement key  
 Low battery indication  
 INPUT mode indication  
 OUTPUT mode indication 
 Reading (measurement) value 

indication 

 Unit (°C / °F) indication 
 Input type indication 

 

Accessories included: 2 pairs of test leads and alligator clips 

Summary of Contents for DC80L














Reviews: