background image

- 8 - 

RN-16TМ 

                                                                                               

NOVATEK-ELECTRO

 

2. TO SET MIN/MAX VOLTAGE THRESHOLDS AND TIME DELAY SETTINGS

 

Perform steps 1-4 from the previous table section “1” (choose the operation mode). 

Ste

p

s

 

Action 

B

u

tto

n

 

Indication 

B

u

tto

n

 

Action 

Indication 

 

Press end enter the 

menu 

 

 

 

 

 

By scrolling buttons find 

U-PA

 mode  

◄►

 

 
 

 

 

 

Press and choose upper 

voltage threshold 

 

 

 
 

 

 

 

Press and while keeping 

button pressed set the 
required upper voltage 
threshold, then release 
the button when the 
setting is done 

 

 

 
 

(blinking dot)

 

◄►

 

Set upper voltage 
threshold value in 
the range 230-320 

 

 
(blinking dot)

   

 

Press and save the 

selected value in the 
device memory (Save 
and Exit) 

 

 

 
 
 

 

 

 

Select LOWER voltage 

threshold 

◄►

 

 
 

 

 

 

Press and while keeping 
button pressed set the 
required lower voltage 
threshold, then release 
the button when the 
setting is done 

 

 
 
(blinking dot)

 

◄►

 

Set lower voltage 
threshold value in 
the range 150-210 

 

 
(blinking dot)

 

Press and save the 

selected value in the 
device memory (Save 
and Exit) 

 

 
 
 
 

◄►

 

Press (calibration of 
the present voltage) 

 
 

NOT 

RECOMMENDED 

TO MAKE ANY 

CHANGES ON 

THIS STEP! 

This function allows to perform precise calibration to the curtain power supply circuit. 
If there is strong requirement it’s possible to change calibration voltage when having 
voltmeter connected in parallel and setting the value shown on the voltmeter. 

Press and while keeping 

button pressed set the 
required value, then 
release the button when 
the setting is done 

 

 

 
 
(blinking dot)

 

◄►

 

Set the voltage 
shown on voltmeter 

 

L_ _ _  

L._ _ _  

L.205  

 

L205  

221.5  

221.5 

Н240

  

SP   1 

U – PA 

Н._ _

 _   

Н.240

  

 

Н_ _ _

    

Summary of Contents for RN-16TM















Reviews: