NovaTec NovaWheel NW Series Instruction Manual Download Page 32

 

NovaWheel Instruction Manual

                                32                            

Document#: IM NW400-2000_10-07-08

 

NW Series NovaWheel Dryer 

INSTRUCTION MANUAL

Warranty:

   

 

 

 

 

 

 

             

 

as of 10/28/2008

 

NOVATEC, INC. offers COMPREHENSIVE PRODUCT WARRANTIES on all of our plastics auxiliary 
equipment.  We warrant each NOVATEC-manufactured product to be free from defects in materials and 
workmanship, under normal use and service for the periods listed under “Warranty Periods”.   The obligation of 
Novatec, under this warranty, is limited to repairing or furnishing, without charge, a similar part to replace any 
part which fails under normal use due to a material or workmanship defect, within its respective warranty 
period. It is the purchaser’s responsibility to provide Novatec with immediate written notice of any such 
suspected defect. Warranted replacement parts will be billed and shipped F.O.B. point of manufacture. A credit 
will be issued when the purchaser returns the suspect defective part. Novatec shall not be held liable for 
damages or delay caused by defects. No allowance will be made for repairs or alterations without the written 
consent or approval of Novatec. 

The provisions in equipment specifications are descriptive, unless expressly stated as warranties. The liability of 
Novatec to the purchaser, except as to title, arising out of the supplying of the said equipment, or its use, 
whether based upon warranty, contract or negligence, shall not in any case exceed the cost of correcting defects 
in the equipment as herein provided. All such liability shall terminate upon the expiration of said warranty 
periods. Novatec shall not in any event be held liable for any special, indirect or consequential damages. 
Commodities not manufactured by Novatec are warranted and guaranteed to Novatec by the original 
manufacturer and then only to the extent that Novatec is able to enforce such warranty or guaranty. Novatec, 
Inc. has not authorized anyone to make any warranty or representation other than the warranty contained here. 
Non-payment of invoice beyond 90 days will invalidate the warranty. A renewed warranty can be purchased 
directly from Novatec. 

NW Series Wheel Dryers…5 years 

Exclusions:  Routine maintenance/replacement parts are excluded from the warranty. These include, 
but are not limited to: hoses, desiccant, filters, filter elements, wiper seals, gaskets, dew point sensors, 
infrared lamps, motors and motor brushes. In addition, the use of abrasive materials will void the 
warranty of any product not specifically sold/designed for use with the specified abrasive material. 
Novatec reserves the right to limit the warranty if the customer installs replacement parts that do not 
meet the specifications of the original parts supplied by Novatec. 

Specific Exclusions:  
Filters 
NovaWheel Control warranty is 2 Years

 

 

This warranty shall not apply to equipment: 

1.

 

Repaired or altered without written approval of NOVATEC unless  

 

such repair or alteration was, in our judgment, not responsible for the failure 

2.

 

Which has been subject to misuse, negligence, accident or incorrect wiring by others 

3.

 

Warranty is void if processing rates exceed manufacturer-recommended levels or if damage is 
caused by ineffective power isolation and/or power spikes/sags or incorrect installation. 

 
 

Form# 200810 Warranty

 

 

 

Summary of Contents for NovaWheel NW Series

































Reviews: