background image

 

 

1. Safety Instructions 

WARNING 

Please  keep this User Guide for future consultation. If you sell the unit to another user, be sure that 

they also receive this instruction manual. 

Important: 

Damages  caused by the disregard of this user manual are not subject to warranty. The dealer

 

will  not accept liability for any resulting defects or problems. 

 

 

 

allow  children to operate the fixture. 

 

 

surfaces. 

sure,  that no ventilation slots are blocked, otherwise the unit will be overheated. 

 

requirements of the unit. 

o  earth in order to avoid electric shock. 

-40

 

-up  some smoke or smell may arise. This is a normal process and does not 

necessarily mean that the device is defective, and it will decrease gradually within  15 minutes. 

 

hazard. 

 

nit’s  surface temperature may reach up to 85

 

. DO NOT touch the housing bare-handed 

during 

its  operation, and allow about 15 minutes for cooling the unit down before replacing bulb or

 

maintenance as it could be very hot. 

ater  or metal objects entering the unit. Once it happens, cut off 

Please  read the instruction carefully which includes important information about

 

the  installation, usage and maintenance. 

the mains power immediately. 

1/12

 

Summary of Contents for VELA 440BSW















Reviews: