Nostalgic AC CK-7486NC Installation Instructions Manual Download Page 11 | Manualshive

Page: 11 / 16

background image

13. We recommend attaching the hoses to the condenser before reinstalling the

radiator.

14. Once the hoses are attached reinstall the Radiator, and shroud
15. Fill the Radiator with the antifreeze and water. You may have to run the Jeep in

order to fill the radiator to its full capacity.

Step Five

Installing the compressor mount and compressor

1. This kit is designed to work with many different engine combinations; Please use

the directions supplied with the mount kit to install the mount, compressor and
belt.

2. The compressor can be mounted with the fittings on the side or straight up.
3. The compressor (if purchased with the kit) will be full of oil. DO NOT ADD OIL

TO THE SYSTEM.

3$*(

«
...
9
10
11
12
13
...
»

Summary of Contents for CK-7486NC

















Reviews:

No comments

Related manuals for CK-7486NC

Brand: NANO Pages: 28

Brand: Daikin Pages: 20

DELUXE HIGH WALL MINI SPLIT

Brand: ICP Pages: 26

C*ED060A Series

Brand: Unitary products group Pages: 24

Brand: ICP Pages: 14

Brand: Daikin Pages: 26

38NY009-012 Series

Brand: Carrier Pages: 9

Comfort Pack CPE U Series

Brand: National Comfort Products Pages: 36

Brand: Acson Pages: 140

Brand: RZB Lighting Pages: 8

Brand: Carrier Pages: 68

IM-CKA-0501 A Series

Brand: McQuay Pages: 39

MADISON 1000 SERIES

Brand: National Comfort Products Pages: 20

Brand: INVENTOR Pages: 80

Brand: Westinghouse Pages: 118

Brand: Kaysun Pages: 16

DOLCECLIMA ARIA 8

Brand: Olimpia splendid Pages: 220

Brand: Kaysun Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands