background image

E

N

G

LI

S

H

10

INSTALLING THE GUARDRAIL

Place the Guardrail on top of the kegorator and align its holes with the holes on the top 

of the kegorator. Secure the Guardrail to the kegorator by placing inside corresponding 

holes. Insert the cover of the drip tray into the base and set under the Tap Tower spout.

TAPPING THE BEER KEG

(SINGLE VALVE-TYPE KEG)

Follow these steps below to tap the Beer Keg.

1. 

Make sure the black pull handle of the Keg Coupler is in the closed (up) 

position before installing it on the keg (Fig. 1). Insert the Keg Coupler into 

the locking neck of the Beer Keg and turn clockwise until it locks into 

position (Fig. 2). This means that it is secured to the Beer Keg.

2. 

Make sure the Beer Tower Faucet is in the closed (handle pointing straight back) position 

before connecting the Keg Coupler to the Keg (Fig. 3). To secure  

the tank connection, pull the Keg Coupler handle out and push down until it locks into 

position. Listen for the “click” of the pull handle when it shifts into the final downward 

position (Fig. 4). This will open the beer and CO2 gas valves. The Keg is now tapped.

 

HOW TO OPERATE

Follow the steps below to dispense beer.

1. 

Make sure that the  kegorator  is plugged in properly to a 

120V, 60Hz, 15 Amps grounded AC outlet.

2. 

Place the drip tray under the beer faucet to avoid messes from excess beer.

3. 

Open the beer faucet by pulling the tap towards you to dispense the beer. If for any reason 

the beer does not come out of the tap, please refer to the 

Tapping the Beer Keg 

section.

4. 

Increase the pressure if the beer runs too slowly (see Regulator section).

5. 

Hold the glass steady at a 45° angle. When it is ²

/ 3

 full, straighten the glass. 

fig. 4

fig. 1

 fig. 2    

fig. 3

Black pull handle

Connect to the
Beer Line Tube

Connect to
CO2 Gas 
Line Tube

Keg Coupler

TU

RN

 CL

OCKWISE

Beer Keg Neck

Keg Support

Beer Keg

Lift Upright

Black pull handle

Connect to the
Beer Line Tube

Connect to
CO2 Gas 
Line Tube

Keg Coupler

TU

RN

 CL

OCKWISE

Beer Keg Neck

Keg Support

Beer Keg

Lift Upright

Blac

k pull handle

Connect to the

Beer Line 

Tube

Connect to

CO2 Gas 

Line 

Tube

Keg Coupler

TU

R

N

 C

LO

C

K

W

IS

E

Beer K

eg Nec

k

Keg Suppor

t

Beer K

eg

Lift Upr

ight

Summary of Contents for KEG7000SS

















Reviews: