Norton GC25E, Owner'S Manual

Page: 8 / 40

8
C. GC55 and GC25E Series Concrete Saw Specifications
Dimensions/Weight GC55 GC25E
Length (Working) 42-23/32” (1,090mm) 42-23/32” (1,090mm)
Length (Transport) 32” (813mm) 32: (813mm)
Width 18-1/8" (460mm) 18-1/8" (460mm)
Height 42-23/32” (1,090mm) 42-23/32” (1,090mm)
Frame Width 18-1/8” (460mm) 18-1/8” (460mm)
Pointer Length 8-7/32” (209mm) 8-7/32”(209mm)
Blade To Wall 7-1/2” (190mm) 7-1/2” (190mm)
Wheel Base Length 19” (483mm) 19” (483mm)
Blade Shaft Maximum Height 9-41/64” (245mm) 9-41/64” (245mm)
Weight Created 135 lbs (61 kg) 155 lbs (71 kg)
Weight Uncreated 115 lbs (52 kg) 135 lbs (61 kg)
Power Source
Engine/Motor Mfg. Honda Gangfon Motor
Spec No. GX160K1QXC Totally Enclosed Air Cooled Thermal
Protection
Power Source Single Cylinder 4 Cycle Gasoline Electric
Maximum Horse Power* 5.5 HP (4.1 kW) 2-1/2 HP
Net Horse Power 4.5 HP (3.4 kW) 2-1/2 HP
Max Torque 7.6 lb-ft (10.3 Nm) @ 2500 rpm -NA-
Power Source RPM 3,600 RPM 3450 RPM
Model GX160 Dual Voltage
Cooling System Forced Air Forced Air
Oil Capacity 0.6 liter (0.63 US qt) -NA-
Fuel Capacity 3.1 liter (3.28 US qt) -NA-
Fuel Type Unleaded Gasoline (86 pump octane) -NA-
Low Oil Sensor Yes -NA-
Air Filtration Four Stage Cyclone -NA-
Voltage -NA- 115-230 volts
Cycles/Current/Phase -NA- 60Hz/AC/1
Full Load Amps (115/230 volts) -NA-
15/7.5 Amps
Starting Amps (115/230 volts)
2
-NA- 45/22.5 Amps
Displacement 9.9 in
3
(0.16 l) -NA-
Bore x Stroke 2.7” (68mm) x 1.8” (45mm) -NA-
Starter Manual Capacitor
Characteristics
Max Blade Ø10" (254mm) Ø10" (254mm)
Depth of Cut 10” (254 mm) 3.5" (88mm) 3.5" (88mm)
8” (203 mm) 2.5" (63mm) 2.5" (63mm)
Arbor Bore 5/8" 5/8"
Blade Shaft Flange Diameter 3-5/64” (78mm) 3-5/64” (78mm)
Blade Shaft Speed 2905 rpm 2905 rpm
Depth Control Hand Wheel With Screw Feed Hand Wheel With Screw Feed
Depth Lock Standard Standard
Depth Gauge Standard Standard
Number Of V-Belts 1 1
Blade Guard Type Screwed On, All Steel Construction Screwed On, All Steel Construction
Cutting Side Center Center
Lifting Bale Built In Built In
Handle Bars Adjustable, Stays Level At All Times Adjustable, Stays Level At All Times
Wheels Non-marking Non-marking
Wheel Size Front and Rear 3-3/8”x2-3/4”x25/32” (85x70x20mm) 3-3/8”x2-3/4”x25/32” (85x70x20mm)
Sound pressure
3
88 db (A) -NA-
Sound power
3
105 db (A) -NA-
1)Net Horsepower Rating provided by engine the manufacturer measured in accordance to SAE j1349 @ 3,600 RPM. The engine may vary from this value.
Actual horsepower on the machine will vary due to operating speed of engine, belt tension, environmental conditions, machine maintenance, and other variables.
2) Starting Amps are instantaneous – for best results use with a 30Amp circuit.
3) The sound measures have been made following pr EN 12638, Annex A; - 2 “Floor sawing, grooving and milling machines – Safety
“