NorthStar NSB12-170RT Applications Manual Download Page 7

Battery Safety

For full information please read the Safety Data Sheet 

(SDS).  The  SDS  document  is  titled  SDS-430-00607 

and  can  be  downloaded  from  the  internet  at  www.

northstarbattery.com

When  dealing  with  Valve  Regulated  Lead  Acid  (VRLA) 

Batteries some additional safety information is required. 

Please read and observe the installation and 

operation instructions.

When working on batteries wear appropriate 

Personal Protective Equipment (PPE). Refer 

to battery MSDS for complete list.

Do not expose the battery to an open flame 

or other ignition source. During operation 

an explosive mixture of hydrogen gas may 

accumulate.
Battery terminals are always energized and, 

if short-circuited, cause electrical arcing. 

Always use insulated tools.

Batteries are heavy objects. Use proper 

handling equipment safety gear during 

installation.

Inappropriate lead acid battery disposal 

can result in environmental contamination. 

Please dispose of batteries according to 

local regulations.
Battery may be returned, shipping pre-paid, 

to the manufacturer or any distributor for 

recycling.

Batteries contain concentrated sulfuric acid 

in water. Any fluid found outside the batteries 

should be regarded as acid. 

Clean all acid splash in eyes or on skin with 

plenty of clean water. Then seek medical 

help. Acid on clothing is to be washed with 

water

Risk of explosion or fire. Avoid any short 

circuit. Metallic parts under voltage on the 

battery, do not place tools or items on top of 

the battery.

Batteries are supplied in a fully charged state and must 

be  unpacked  carefully  to  avoid  very  high  short-circuit 

currents terminals of opposite polarity. Use care when 

handling  and  moving  batteries.  Appropriate  lifting 

equipment must be used.

Pb

Pb

6.1 

Keep away from open flames

In case of accidental overcharge, a flammable gas can 

leak from the safety vent. Discharge any possible static 

electricity from clothes by touching an earth connected 

part.

6.2       Tools

Use tools with insulated handles. Do not place or drop 

metal  objects  on  the  battery.  Remove  rings,  wrist 

watches and articles of clothing with metal parts that 

may come into contact with the battery terminals.

Determining Battery Manufacturing Date

Location of Serial Numbers

The battery serial numbers are located in two places on 

the battery case. 

The first is on the front of the battery. The manufacturing 

date is also located on this label below the serial number.

 

 

Form:  SES-541-01711

Issued:  12-08-16

ECO-101191

Summary of Contents for NSB12-170RT














Reviews: