Northline Express Smart-Holder Instruction Manual Download Page 2

Because a chainsaw is a 

high-speed, wood-cutting  

tool some 

special safety 

precautions

 must be 

observed in addition to 

those that generally apply when working 

with an axe or hand saw.

It is important that you 

read and understand the 

owner’s manual before 

using your tool for the first 

time. Non-observance of 

the following safety 

precautions may cause serious or even 

fatal injury.
Read and observe the instructions in the 

chainsaw manual – especially the safety 

precautions.
Always observe local safety regulations, 

standards and ordinances.
If you have never used a chainsaw 

before: 

Have your

   

 

 

 

dealer show you how 

to operate the chainsaw or attend a 

special course of training in chainsaw 

operation. 

Minors should never be allowed to use a 

chainsaw or the sawbuck.

Bystanders, especially children, and 

animals should not be allowed in the 

area where a sawbuck and chainsaw 

are in use.
The operator is responsible for avoiding 

injury to third parties and damage to 

their property.
You must be in good physical condition 

and mental health to operate a power 

tool and not under the influence of any 

substance (drugs, alcohol) which might 

impair vision, dexterity or judgment.

Clothing and Equipment

Wear proper protective clothing and 

equipment.

Clothing must be sturdy 

and snug-fitting, but allow 

complete freedom of 

movement. Wear overalls 

or jeans with a reinforced 

cut retardant insert or cut 

retardant chaps - a safety 

combination is recommended.
Avoid loose-fitting jackets, scarfs, 

neckties, jewelry or anything that could 

become entangled. Confine long hair 

(e.g. with a hair net).

Wear steel-toed 

safety 

boots

 with non-slip 

soles.

Wear 

safety glasses 

and

 

 

hearing protection

 

(earplugs or earmuffs).

Wear 

heavy-duty, 

non-slip gloves

preferably made of 

chrome leather.

Spikes

The spikes of the support and spike 

frame are very sharp. Handle with care 

to reduce the risk of injury.

Safety Precautions

.

 

Toll-Free

 1-866-667-8454 

NorthlineExpress.com

www.NorthlineExpress.com

Summary of Contents for Smart-Holder







Reviews: