Step
5 If camera base installation applied, press the arrows
marked on the lining to remove the lining aside. Unscrew
the three black screws and put them aside. Turn the
camera base clockwise for 5 degrees and remove it, as
shown in figure 3-5.
Figure 3-3
Opening camera
Step 7 View the video, adjust the lens angle horizontally and
vertically, Set the value in the Front-end Configuration for
AF lens and use the focusing lever for MF lens to adjust
the lens Focal length and video angle range.
Figure 3-5
Removing lining and base
Step 1
Remove the upper cover.
For Plastic dome, press down the dome with one hand at
position marked by an arrow, rotate the upper cover of the
dome counterclockwise with the other hand, and gently
pull the upper cover upward to remove it, as shown in
Figure 3-3.
For vandal dome, use the T15 screw driver in the
accessory package to unscrew the three screws on the
dome cover. The camera is opened, as shown in figure 3-3.
The vandal dome camera can be installed in the ceiling , wall ,
wall bracket or ceiling bracket. This section describes how to
install the camera in the ceiling.
WARNING
To avoid moisture influence, install the dome cover at least
half an hour after the camera is installed and powered on.
Base
Screws
Unscrew
Arrows
Base
Top
routing
Figure 3-6
Installing base
Aside routing
Black
screws
lining
cover
Four
buttons
Figure3
-
8
Assembling
lining and base
Adjust the Focal
length and viedo
angle range
Main
body
fixation
screws
F
igure3
-
7
Adjusting
lens
3 Device
Installation
Figure 2
-
5
Dimensions
（
Unit:mm
）
Figure 2
-
6
Plastic Dome
Dimensions
（
Unit:mm
）
63
∅
77
∅
95
64.3
31
∅
5
∅
5.5
M9
4-M3
3-M3
4-M2
∅
95
120.3
129.9
58
1
1
1.5
8°
100°
137°
∅
110
Figure 2
-
7
Vandal dome Dimensions
（
Unit:mm
）
1
1
1.5
59.2
97.4
130
∅
110.4
8°
100°
137°
Step1
Stick the Installation location sticker on the ceiling or wall,
Drill three holes based on the marks on the sticker. Drive
the swell plastic buttons into the holes.
Step
2
Fix shell with screws to the ceiling directly for ceiling
installation, as shown in Figure 3-1.
Install bracket mount plate to the ceiling or wall with screws
for wall installation, as shown in Figure 3-2.
3.1 Installation for camera in Figure 2-6.
Figure 3
-
1
Ceiling installation
Step 3 Detach protection vinyl from the dome cover.
Figure 3
-
2
Wall installation
3.2 Installation for other cameras.
Step 2 Stick the Installation location sticker on the ceiling or wall,
Drill three holes based on the marks on the sticker. Drive
the swell plastic buttons into the holes.
Step
3
Connect the multi-head cable(If camera base installation
and aside routing selected, this step is operated after step
5).
Step 4 If camera housing installation applied, Fetch three black
self-tapping screws from the accessory package. Then fix
the screws to fasten the camera on the ceiling as shown in
figure 3-4.
Plastic dome
Vandal dome
Figure
3
-
4
Installing housing
Installation Option 1:
Use holes marked with 'A' when
installing camera base first.
Use short ( 1.2inch length) screws and anchors
Installation Option 2:
Use holes marked with 'B' when
installing complete camera housing.
Use long ( 2.75 inch length) screws and an-
chors
A
A
A
B
B
B
Aside routing
Swell plastic
buttons
Self-tapping
screws
Top
routing
Black
screws
Plug
Step 6 Aim the three through-holes on the camera base at the
three swell plastic buttons in the ceiling, and use screws
with a length of 30 mm to fix the base on the ceiling. Turn
the main body clockwise for about 5 degrees to assembly it
with the camera base, and fix the three screws, as shown
in figure 3-6.
T15
screwdriver
Step 8 Assemble the lining with the main body and buckle the
four button placements with the main body bracket. . Then
fasten the dome cover, as shown in Figure 3-8.
3
.
3
Embedded Installation for plastic dome
Step 1 Remove the upper cover and the lower cover.
Step 2 Take the embedded installation location sticker, drill a hole
basing on the inner edge of the sticker.
Step 3 Put into the hole and attach it to the installation surface,
hold the dome with one hand, and fasten the screws with
the other hand till touches the inner side of the
installation surface, and fasten the dome, as shown in
figure 3-9.
e
c
d
Plastic dome
Vandal dome
Step 4 Take the video patch cord out of the accessory, connect the
RCA end of the line to the second video output port, and
connect the BNC end of the line to a monitor for tests.
Step 5 Remove the linling and adjust the angle of the camera, fix
the focusing lever, and adjust the lens angle as required.
Step 6 Install the linling and the upper cover.
NOTE
By default, the focusing lever is locked. To adjust the focusing
lever, loosen it in counterclockwise direction and then tighten it
after adjustment.
F
igure 3
-
9 Embedded Installation
c
2
d
e
e
