background image

O6140  03/03

4

INTRODUCTION

Servicing of marine engines and generator sets 
presents unique problems.  In many cases boats 
cannot be moved to a repair facility.  Marine 
engines cannot be compared to the servicing of 
automobiles, trucks or even farm equipment.  
Failures often occur in remote areas far from 
competent assistance.  Marine engines are taxed 
far more severely than auto or truck engines; 
therefore, maintenance schedules must be 
adhered to more strictly.  Failures usually begin 

with minor problems that become ampli

fi

 ed 

when not corrected during routine mainte-
nance.

As owner-operator, it is your obligation to 
learn about your equipment and its proper 
maintenance.  This manual is not a comprehen-
sive technical service manual.  Nor will it make 
the reader into an expert mechanic. Its aim is 
to aid you in maintaining and servicing your 
equipment properly. 

Northern Lights aftercooled-turbocharged 1200 
RPM marine diesel generator set.  Komatsu 6140 
block.

Northern Lights turbocharged-aftercooled 1500 or 
1800 RPM industrial diesel generator set.
Komatsu 6140 block.

NL

6140

A

M

6140

QA

 

L

 - Lugger marine propulsion engine 

Model number of 

A

 - Aftercooled (turbo)

 

M

 - Northern Lights marine generator set 

Komatsu engine block 

AL2 

- Aftercooled (turbo- 

 NL

 - Northern Lights industrial generator set 

6 cylinder, 140 mm bore 

        low profi le)

 

 

 

D

 - Naturally aspirated

 

 

 

T

 - Turbocharged

 

 

 

QA 

- 1200 RPM (Aftercooled)

 

 

 

MODEL NUMBER

Model numbers give unit's application, block model, aspiration and RPM:

 

L - M - NL 

6140 

AL, D, T, & Q

UNIT IDENTIFICATION

Lugger turbocharged-aftercooled marine propulsion 
engine.  Komatsu 6140 block.  (low profi le)

Lugger turbocharged-aftercooled marine propulsion 
engine.  Komatsu 6140 block.  (high profi le)

Northern Lights turbocharged 1500 or 1800 RPM 
marine diesel generator set.  Komatsu 6140 block.

SERIAL NUMBERS

When referencing Alaska Diesel Electric equipment by serial number, refer only to the number 
stamped on the Lugger or Northern Lights serial number plate.

L

6140

AL2

M

6140

AL2

L

6140

A

Summary of Contents for LUGGER L6140A




































Reviews: