North SELEKT BRD Operating Manual Download | Manualshive

Page: 2 / 32

background image

Read and understand this entire Manual and your employer

’s safety practices before installing, oper-

ating, or servicing this Product. While the information contained in this Manual represents the Manu-

facturer’s best judgment, the Manufacturer assumes no liability for its use

.

User Manual No: OM-101A EN

for: SELEKT BZL, PNA, TWE, BRD Style MIG/MAG Manual Welding

Torches

SELEKT

MIG/MAG Manual Welding Torch

Model Number

BZL

SN15F-3E, SN15F-4E, SN15F-5E; SN15FE-3E, SN15FE-4E, SN15FE-5E; SN24F-3E, SN24F-4E, SN24F-5E;
SN25F-3E, SN25F-4E, SN25F-5E; SN26F-3E, SN26F-4E, SN26F-5E; SNF36-3E, SNF36-4E, SNF36-5E;
SNF38-3E, SNF38-4E, SNF38-5E; SN40F-3E, SN40F-4E, SN40F-5E; SN240F-3E, SN240F-4E, SN240F-5E;
SN410F-3E, SN410F-4E, SN410F-5E; SN510F-3E, SN510F-4E, SN510F-5E

PNA

SQTB200-3K, SQTB200-4K, SQTB200-5K; SQTB350-3K, SQTB350-4K, SQTB350-5K;
SQTB500-3K, SQTB500-4K, SQTB500-5K; SQTB600-3K, SQTB600-4K, SQTB600-5K

TWE

SNT1-10E, SNT1-12E, SNT1-15E; SNT1-10T, SNT1-12T, SNT1-15T;
SNT1-10L, SNT1-12L, SNT1-15L; SNT1-10M, SNT1-12M, SNT1-15M;
SNT2-10E, SNT2-12E, SNT2-15E; SNT2-10T, SNT2-12T, SNT2-15T;
SNT2-10L, SNT2-12L, SNT2-15L; SNT2-10M, SNT2-12M, SNT2-15M;
SNT4-10E, SNT4-12E, SNT4-15E; SNT4-10T, SNT4-12T, SNT4-15T;
SNT4-10L, SNT4-12L, SNT4-15L; SNT4-10M, SNT4-12M, SNT4-15M;
SNT5-10E, SNT5-12E, SNT5-15E; SNT5-10T, SNT5-12T, SNT5-15T;
SNT5-10L, SNT5-12L, SNT5-15L; SNT5-10M, SNT5-12M, SNT5-15M

BRD

SNQ200-10M, SNQ200-12M, SNQ200-15M; SNQ200-10E, SNQ200-12E, SNQ200-15E;
SNQ300-10M, SNQ300-12M, SNQ300-15M; SNQ300-10E, SNQ300-12E, SNQ300-15E;
SNQ400-10M, SNQ400-12M, SNQ400-15M; SNQ400-10E, SNQ400-12E, SNQ400-15E

Published by: Jinan North Welding Tools Co Ltd

The North of 308 National Highway, Daqiao Town,
Tianqiao Zone, Jinan 250121, Shandong, China.

Website:

www.northweld.com

Copyright © 2018 by: Jinan North Welding Tools Co. Ltd.

® All rights reserved.

Reproduction of this User Manual, in whole or in part, without written permission of the publisher is prohib-
ited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage caused
by any error or omission in this User Manual, whether such error results from negligence, accident, or any
other cause.

Publication Date: May 2020

Record the following information for Warranty purposes

Place of Purchase:

Purchase Date:

«
1
2
3
4
...
»

Summary of Contents for SELEKT BRD

































Reviews:

No comments

Related manuals for SELEKT BRD

Brand: Yarkiy Luch Pages: 2

Red Dot SiteLight K780

Brand: Thomas & Betts Pages: 2

MacoLEDs R8/22-200C

Brand: Macostar Pages: 5

Brand: Sealey Pages: 2

NightSearcher Solaris Pro

Brand: Maxi Led Pages: 7

Brand: WE-EF Pages: 8

Brand: N'oveen Pages: 25

MagniFlach CP-40

Brand: Carson Pages: 2

Brand: Vimar Pages: 4

Brand: Alecto Pages: 2

LED PAR 38 TRI-B

Brand: Chauvet Pages: 20

Brand: Mr. Heater Pages: 24

Brand: WowWee Pages: 68

Brand: Showline Pages: 8

LED12.BB-12/24-350-XP

Brand: Western Pages: 6

Brand: Sealey Pages: 2

OPTIMAX Jr. OPX-500

Brand: Spectroline Pages: 2

OPTI-LUX 365 Series

Brand: Spectroline Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands