manualshive.com logo in svg

North Atlantic SRS 5330A, Operation Manual

Share
Download
North Atlantic SRS 5330A Operation Manual Download Page 20

 

North Atlantic Industries, Inc.

 

631.567.1100 / 631.567.1823 (fax)                       

6/12/2018 

5330A Operations Manual Rev A6 

110 Wilbur Place, Bohemia, NY 11716 

www.naii.com              

Cage Code: 0VGU1 

Page 20 of  24 

 

 
 
 
Repair 

DO NOT ATTEMPT REPAIRS.

 All repairs to this instrument must be accomplished at the Factory. 

 

High Voltage 

is used in the operation of this equipment. 

 
 

DEATH  ON  CONTACT 

may  result  if  personnel  fail  to  observe  safety  precautions.  Be  careful  not  to 

contact high-voltage connections when installing, operating or maintaining this instrument. 

 

 
Input Power Always On  

AC input power is continuously supplied to the power supply independent of the front panel ON/OFF Switch. The 
primary means of disconnect is to remove the line cord from the instrument  

 

 
Rear Panel Cooling Fan Filter 

The  unit  is  equipped  with  a  cooling  fan  installed  on  the  rear  panel  of  the  unit.  The  Fan  Filter  Assembly  is  user 
accessible  and  the  Fan  Filter  has  been  mounted  for  easy  removal  for  cleaning  and/or  replacement.  Periodic 
inspection  (duration  varies  upon  unit  environmental  use)  of  the  condition  of  the  filter  is  recommended  to  insure 
proper  air  flow  circulation  and  reduction  of  contaminants.  If  filter  is  clogged  or  deteriorated,  cleaning  and/or 
replacement  is  recommended.  The  Fan  Filter  is  held  in  place  by  a  filter  shroud  insert.  Before  any  maintenance  is 
performed, insure that the  power cord has been disconnected from the unit. The  filter shroud can be removed (no 
special  tools  required)  by  gentling  pulling  and  disconnecting  from  the  shroud  assembly  (insert  is  held  in  place  by 
molded retainers in the shroud). The filter can be  accessed  at  this  point for maintenance.  Two spare replacement 
filters are supplied in the accessory kit. 

 

 

 
 
 
 
 
 
 
 
 
 
 

 

Figure 26 

– Maintenance; Cooling Fan Filter 

 

C

ALIBRATION

 

Self-calibration  

The unit is self-calibrating. When unit is turned on it will automatically initiate self-calibration. After warm-up of 15 
minutes,  unit  will  again  automatically  calibrate  the  channel  or  channels  being  used.  Once  calibrated,  unit  will 
monitor  usage.  Should  frequency  or  voltage  of  output  signal  change/commanded  by  more  than  12.5%,  unit  will 
automatically recalibrate the channel in use. Calibration takes about 2 seconds. 

Calibration Verification 

The model 5330A should have its calibration verified on an annual basis. Factory Calibration service is available on 
request. If the instrument fails to meet its accuracy, it must be repaired. Repairs can only be done at the Factory. 

 

Summary of Contents for SRS 5330A

























Reviews:

No comments

Brands by name

Popular brands

Load more brands