manualshive.com logo in svg

North Atlantic SRS 5330A, Operation Manual

Share
Download
North Atlantic SRS 5330A Operation Manual Download Page 18

 

North Atlantic Industries, Inc.

 

631.567.1100 / 631.567.1823 (fax)                       

6/12/2018 

5330A Operations Manual Rev A6 

110 Wilbur Place, Bohemia, NY 11716 

www.naii.com              

Cage Code: 0VGU1 

Page 18 of  24 

 

 
 

 
O

RDERING 

I

NFORMATION

 

 

 

 Part number: 5330A - 

 

 

- 

 

 

                                             
                                                            

Leave blank for standard 5330A 

 

              

Add ‘30’ ** for a for a replacement for all legacy 5330 models 

 

              

Add ‘10’ for a for a replacement for all legacy 5310 models 

 

        

                                                                      

Add ‘0’ for no reference supply; add ‘R’ for one reference supply 

 
                                                                      

Add ‘1’ for single channel; add ‘2’ for two channels 

 
 

 

**Note: To mimic the connector pin-out of the 5330, a separate conversion cable (P/N 07-0022) must be ordered.   

 
 
Accessories: 

Included

 with the 5330A is an accessory kit NAI part number 5330A-ACCESSORY-KIT. 

Kit includes the following items: 
 

5330A- Accessory Kit 

NAI P/N 

5310  Accessory Kit 

NAI P/N 

5330  Accessory Kit 

NAI P/N 

78 Pin Mating connector   09-0001 

50 Pin Mating 
connector 

05-0053 

Fuse, 5 x 20mm, 
2A, slow-blow (2) 

99-0146 

Shell 

P/O 09-0001  Shell 

05-0060 

Line Cord 

202-0002 

Fuse, 5 x 20mm, 2A, 
slow-blow (2) 

99-0146 

Fuse, 5 x 20mm, 2A, 
slow-blow (2) 

99-0146 

Two spare fan 
filters 

111-0005 

Line Cord 

202-0002 

Line Cord 

202-0002 

 

 

Two spare fan filters 

111-0005 

Two spare fan filters  111-0005 

 

 

 

Optional Mounting Accessory 

The  5330A  can  be  ordered  with mounting  adapters  for  one unit  in  a  standard  19-inch  equipment rack.  The  table 
below describes full rack mounting accessory: 
 

Type of Mount 

Description 

NAI P/N 

 
Full Rack Mounting 

 
Mounts one unit in a 19-inch rack 

 
783893 

 
 
 

 
 
 
 

 

Summary of Contents for SRS 5330A

























Reviews:

No comments

Brands by name

Popular brands

Load more brands