Nortel Passport 4400 Series Hardware Installation Manual Download Page 103

Page: 103 / 144

T1/E1 and Digital Voice Modules

Passport 4400 Hardware Installation Manual

9-9

Procedure 16:

Removing a Digital Voice Module

Unlatch the first Digital Voice Module from its mating connector in the T1

Voice Module, the E1 Voice Module, or the Digital Voice Expansion Module.
To do that, press your thumbs against the latch springs at either end of the
module, and with your forefingers turn the Digital Voice Module into the
upright position.

Lift the Digital Voice Module out of the connector.

Repeat steps 1 and 2, and sequentially remove the remaining applicable
Digital Voice Modules.

Figure 9-11. Digital Voice Module Replacement

T1 or E1 Voice Module

Digital Voice
Expansion Module

Notch

Summary of Contents for Passport 4400 Series

















































































































































Search results

Summary of Contents for Passport 4400 Series

Reviews:

Related manuals for Passport 4400 Series

Brands by name

Popular brands

Nortel Passport 4400 Series, Hardware Installation Manual

Search results

Summary of Contents for Passport 4400 Series

Reviews:

Related manuals for Passport 4400 Series

Brands by name

Popular brands