manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 171 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 171

Chapter 4 Getting Started with Device Manager

171

System Configuration Guide

 

Device Manager basics

This section describes basic procedures for using the Device Manager software. 
The section includes the following information:

•

“Starting Device Manager”

•

“Setting the Device Manager properties” on page 172

•

“Opening a device” on page 174

•

“Device Manager window” on page 177

•

“Editing objects” on page 186

•

“Working with statistics and graphs” on page 186

•

“Telnet session” on page 193

•

“Opening an SSH connection to the device” on page 194

•

“Opening the Web-based management home page” on page 194

•

“Trap log” on page 195

•

“Online Help” on page 196

Starting Device Manager

➨

Do one of the following, depending upon your operating system environment:

•

In a Microsoft

*

 Windows

* 

environment, choose All Programs > Nortel > 

Java Device Manager > DM from the Windows Start menu.

•

In a UNIX environment, verify that the Device Manager installation 
directory is in your search path; then enter:

./JDM

The initial Device Manager window opens 

(Figure 54)

.

Note: 

On startup, the Device Manager performs a DNS lookup for the 

machine on which it is running. If the DNS lookup is slow or fails, the 
initial Device Manager window may take up to 30 seconds to open.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments