Nortel 425-24T Configuration Manual Download Page 194

Page: 194 / 488

194

Chapter 4 Getting Started with Device Manager

320985-A Rev 01

A Telnet window to the switch opens.

Opening an SSH connection to the device

From Device Manager, you can initiate a Secure Shell (SSH) connection to the
Console Interface for the switch or stack you are currently accessing.

To open an SSH connection to a device:

➨

Do one of the following:

•

From the Device Manager main menu, choose

Device > SSH

Connection

•

On the toolbar, click the

SSH

button.

An SSH window to the device opens.

Opening the Web-based management home page

From the Device Manager, you can access the Web-based management home
page.

To open the Web-based management home page:

➨

Do one of the following:

Note:

The SSH connection is established only when the device is SSH

capable and enabled. For more information on SSH connections, refer to

Configuring and Managing Security for Nortel Ethernet Switches
325 and 425, Software Release 3.6

(320988-A).

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 194 / 488

Search results

Summary of Contents for 425-24T

Reviews: