manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 195 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 195

Chapter 4 Getting Started with Device Manager

195

System Configuration Guide

 

•

From the Device Manager main menu, choose

 Actions > Open Home 

Page

. 

•

On the toolbar, click the 

Open Home Page

 button.

The Web-based management home page opens 

(Figure 71)

.

Figure 71   

Web-based management home page

Trap log

You can configure an Ethernet Switch 325/425 to send SNMP generic traps. 
When the Device Manager is running, any traps received are recorded in the trap 
log. You set the maximum number of entries in the trap log using the Properties 
dialog box 

(Figure 55 on page 173)

. The default number of trap log entries is 500.

To view the trap log:

➨

Do one of the following:

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments