Nortel 1800 Installing Download Page 39 | Manualshive

Page: 39 / 62

background image

39

Installing the Metro Ethernet Services Unit 1800

Chapter 4
Installing SFP GBIC and CWDM SFP GBIC
modules

The Nortel* Metro Ethernet Services Unit 1800-24T provides two bays that
accept SFP GBIC and CWDM SFP GBIC fiber optic modules. These modules,
which operate at 1000 Mbps in full-duplex mode, allow Gigabit Ethernet ports to
connect to fiber optic networks.

This chapter includes the following topics:

Supported SFP GBIC and CWDM SFP GBIC modules

The following sections describe the supported SFP GBIC and CWDM SFP GBIC
modules.

Topic

Page

Supported SFP GBIC and CWDM SFP GBIC modules

Inserting and removing SFP GBIC and CWDM SFP GBIC modules

Inserting and removing an SFP GBIC fiber optic cable

Caution:

The Metro ESU 1800-24T-DC was tested with a selection of

SFP modules. The Regulatory Certifications are valid only under the
condition of using SFP modules that have been approved for this system.
While by their design other SFP modules work, it cannot be guaranteed
they meet all the regulatory requirements when installed in the Metro
ESU 1800-24T (AC power supply) or ESU 1800-24T (DC power supply).

«
...
37
38
39
40
41
...
»

Summary of Contents for 1800































































Reviews:

No comments

Related manuals for 1800

Brand: Vanguard Pages: 121

Brand: X-Micro Pages: 74

Brand: Salto Pages: 2

Brand: Juniper Pages: 502

Brand: Commell Pages: 9

MultiConnect SE MTS2EA

Brand: Multitech Pages: 8

Brand: SAGEMCOM Pages: 75

Brand: insys icom Pages: 4

Brand: Crystal Vision Pages: 54

Brand: ZiLOG Pages: 317

CyberSWITCH CSX101

Brand: Cabletron Systems Pages: 72

Brand: B+B SmartWorx Pages: 50

Brand: Cradlepoint Pages: 2

Brand: Wistron NeWeb Pages: 32

Brand: ST Pages: 37

FusionHDTV 5 GOLD

Brand: Dvico Pages: 64

Brand: EKF Pages: 40

Brand: I-Tech Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands