manualshive.com logo in svg

Nortel 1800, Installing

Share
Download
Nortel 1800 Installing Download Page 19

19

Installing the Metro Ethernet Services Unit 1800

Chapter 1
Introducing the Metro Ethernet Services Unit 1800

This chapter introduces the Nortel* Metro Ethernet Services Unit 1800 (Metro 
ESU 1800) and discusses its components. Specifically, the chapter includes the 
following topics:

Metro Ethernet Services Unit 1800

Three models of the Metro Ethernet Services Unit 1800 are available:

•

1800-24T-LX-DC—includes 24 10BASE-T/100BASE-TX (UTP) Fast 
Ethernet ports and two Gigabit Ethernet (GE) 1000BASE-LX duplex SC type 
fiber optic transceiver trunk ports. This model includes a single –48V DC 
power supply.

•

1800-24T—includes 24 10BASE-T/100BASE-TX (UTP) Fast Ethernet ports 
and two Gigabit Ethernet (GE) trunk ports with bays for Small Form Factor 
Pluggable (SFP) Gigabit Interface Converters (GBICs). This model includes a 
single 110/220 AC power supply.

•

1800-24T-DC includes 24 10BASE-T/100BASE-TX (UTP) Fast Ethernet 
ports and two Gigabit Ethernet (GE) trunk ports with two Small Form Factor 
Pluggable (SFP) Gigabit Interface Converters (GBICs). This model includes a 
single –48V DC power supply.

Topic

Page

Metro Ethernet Services Unit 1800

19

Enclosure

22

Power supply

22

Cooling fans

22

Summary of Contents for 1800































































Reviews:

No comments

Brands by name

Popular brands

Load more brands