background image

12

Air Filter(s)

 - B6BW air handlers are supplied with a single 

air filter when shipped from the factory. It is recommended 

that the filter be cleaned or replaced monthly.

 WARNING:

Never operate the furnace without a filter in 

place. Dust and lint in the return air can build 

up on internal components, resulting in loss of 

efficiency, equipment damage, and possible fire.

Newly built or recently renovated homes may require 

more frequent changing until the construction dust has 

minimized. Filter sizes shown in 

Table 4

 are available at 

most local retailers.
Filters designed to remove smaller particles such as 

pollen, may require additional maintenance.

Blower Compartment 

- Dirt and lint can create excessive 

loads on the motor resulting in higher than normal operating 

temperatures and shortened service life. It is recommended 

that the blower compartment be cleaned of dirt or lint 

that may have accumulated in the compartment or on 

the blower and motor as part of the annual inspection.

Blower Fan Wheel

 - Inspect the blower wheel blades 

for accumulations of dirt and clean if necessary. Inspect 

mounting nut for tightness when done.

Blower Motor & Assembly

 - Inspect the blower assembly 

and motor mounting brackets for tightness and corrosion. 

Correct deficiencies if necessary. The blower motor 

contains sealed bearings and under normal operating 

conditions, no maintenance is necessary for the life of 

the equipment.

RED LED (AN2)

DIAGNOSTIC DESCRIPTION

OFF

Control Fault (No Power)

Flash

Blower Fault

ON

Normal Operation

Table 5. Furnace Control Board Fault Conditions

TROUBLESHOOTING

If the air handler fails to operate, check the following:

•  Is the electric turned on?

•  Is the thermostat operating properly?

•  Are the blower compartment door(s) in place?

•  Is the furnace disconnect closed?

• Has the circuit breaker tripped or the control board 

fuse burned open?

•  Are any manual reset switches open?

•  Is the filter dirty or plugged?

• Is the LED on the furnace control board constantly 

ON? If not, refer to 

Table 5

 to determine fault condition.

Table 4. Filter Sizes

MODEL NUMBER

FILTER SIZE

B6BW-018K

16” x 20 x 1”

B6BW-019K

20” x 20 x 1”

B6BW-024K

16” x 20 x 1”

B6BW-030K

20” x 20 x 1”

B6BW-036K

24” x 20 x 1”

Summary of Contents for B6BW Series





















Reviews: