manualshive.com logo in svg

Nortec MH Series, Installation Manual, Page: 30 / 60

Share
Download
Nortec MH Series Installation Manual Download Page 30

 

 

10-10 

Page 26 
2008-12-03

 

 

Figure 7.   Mounting Process – Step 7

 
The air gap between the outermost vertical supports and the duct walls as well as between the 
front bracket and the duct ceiling must be sealed using EPDM sealing profile (accessory).  Cut the EPDM 
sealing profiles to the desired length (channel height and channel width plus cm allowance). Fix the 
EPDM sealing profiles to the outermost vertical supports and to the front bracket using the clamping 
brackets and self-tapping screws #10 x 3/4" supplied. Tailor the EPDM sealing profiles to the duct height 
and the duct width, then fix them to the duct walls and the duct ceiling using the clamping brackets and 
self-tapping screws #10 x 3/4" supplied (number of self-tapping screws to be used as required). 
 
Note: In place of the EPDM sealing profiles also sheet metal angles of stainless steel (not included 
in the delivery) may be used for the sealing. 

Summary of Contents for MH Series





























































Reviews:

No comments