background image

SK90

© NØRSE

7

© NØRSE

English

The following cleaning procedure will ensure that you achieve the 
most beneficial results in the shortest amount of time. Use the 
detergent nozzle to apply detergent. Some cleaning tasks can be 
completed with water alone, but for most tasks the removal of dirt 
becomes more effective if a detergent is used.

NOTE:

 Only use mild, environmentally friendly detergents. Never 

use aggressive chemicals, abrasive detergents or similar to avoid 
damage to your health, the product and the environment.

Surface preparation

Clear the working area and make sure that all windows and doors are closed tightly. Make sure that all 
plants and trees adjacent to the cleaning area are protected by a drop cloth.

Initial high pressure rinse

The next step is to spray the cleaning surface with water to clear off any dirt or grime that may have 
collected on the surface. If you use detergent, this will allow your detergent to attack the dirt that has 
worked its way into the cleaning surface. Before triggering the gun, adjust the nozzle to a wide spray 
pattern and slowly adjust to the desired spray pattern. This will help you avoid applying too much 
pressure to the surface that could cause damage.

Detergent application

Only use detergents formulated for pressure washers. Test the detergent in an inconspicuous area before 
use. Follow the manufacturer’s label directions for mixing the correct concentrations of detergent to 
water.

1.   Unscrew the top of detergent applicator and fill with detergent.
2.  Put the top of detergent applicator back on.
3.  Attach the detergent bottle to the end of the fixed spray nozzle, click into place.
4.   Apply the detergent so it thoroughly covers the cleaning surface. Apply from bottom to top to prevent 

the detergent from sliding down and streaking.

5.  Allow the detergent to remain on the surface for a few minutes. This is a good time to use a brush to 

lightly scrub heavily soiled areas. Never allow detergent to dry on the cleaning surface.

6.  Remove detergent bottle from the fixed spray nozzle.
7.  Rinse detergent from surface.

8.   Rinse the detergent bottle with clean water following each use.

9.  Final rinse

Make sure you thoroughly rinse the surface and that all detergent has been removed.

Detergent

Summary of Contents for SK90














Reviews: