background image

SBA8383

Rev. 09/09

NH199-DV

 

 (Indoor Installation)

NH150-DV

 

 (Indoor Installation)

GAS-FIRED DIRECT VENT BOILER

NORITZ AMERICA
CORPORATION

Potential dangers from accidents during installation and use are divided into the following three
categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Disconnect
Power

Ground

Be sure to do

WARNING:

 If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.

DANGER

WARNING

CAUTION

Requests to Installers

Installation must conform with local codes, or in the ab-
sence of local codes, the National Fuel Gas Code, ANSI
Z223.1/NFPA 54- latest edition and/or CSA B149.1, Natu-
ral Gas and Propane Installation Code (NSCNGPIC).
Where required by the authority having jurisdiction, the in-
stallation must conform to the Standard for Controls and
Safety Devices for Automatically Fired Boilers, ANSI/
ASME CSD-1.

Noritz America reserves the right to discontinue, or
change at any time, the designs and/or specifications of its
products without notice.

CAUTION

Noritz America Corporation
11160 Grace Avenue,
Fountain Valley, CA  92708
www.noritz.com

Installation and Instruction Manual

• In order to use the boiler safely, read this installation and instruction manual carefully, and follow

the installation instructions.

• Failures and damage caused by erroneous work or work not as instructed in this manual are not

covered by the warranty.

• Check that the installation was done properly in accordance with this installation and instruction

manual upon completion.

• After completing installation, please either place this installation and instruction manual  in a

plastic pouch and attach it to the side of the boiler or hand it to the customer. Also, be sure to fill in
all of the required items on the warranty and to hand the warranty to the customer along with the
User's information manual.

Low NOx

Approved by

SCAQMD

CERTIFIED

R

Accepted For Use

City of New York

Department of Buildings

MEA 20-07-E

*SBA8383*

Summary of Contents for NH150-DV





























































Reviews: